DAVIS 6152 Скачать руководство пользователя страница 41

Страница: 41 / 60

Vantage Pro2 Troubleshooting Guide

ind Speed

Wind speed reading seems

too high or too low.

For low readings, remove wind cups and check for friction

sources. Check the anemometer location. Is it sheltered from

the wind? See ISS manual for additional wind speed

troubleshooting information.

Wind speed reads 0 either

all the time or intermittently

The problem may be with the anemometer. Test anemometer

by spinning wind cups. Check anemometer switch fields on di-

agnostic screen (see page 39) and call technical support.

Dew

Dew Point reading seems

too high or too low

Check calibration numbers for temperature. Dew point depends

on temperature and outside humidity. Make sure they are

working.

Temperature

Outside temperature sen-

sor reading seems too high

Check to see if ISS is near mechanical or radiant heat source.

Check calibration number and adjust if necessary. ISS or temp

sensor may need to be relocated. See ISS or other transmitter

manual.

Inside temperature sensor

reading seems too high

Move the console out of direct sunlight. Make sure that the

console or sensor is not in contact with an exterior wall that

heats up in sunlight or when outside temperature rises. Make

sure the console or sensor is not near a heater or other internal

heat source (lamps, appliances, etc.). Also make sure the

console backlight is not on. Check calibration number and

adjust if necessary.

Outside temperature

seems too low

Check calibration number and adjust if necessary. Sprinklers

may be hitting the ISS radiation shield. Relocate. See ISS

manual.

Inside temperature sensor

reading seems too low

Make sure the console or other temperature sensor is not in

contact with an exterior wall that cools down when outside

temperature drops. Make sure the console or other temperature

sensor is not near an air conditioning vent. Check calibration

number and adjust if necessary.

ind Direction

Wind direction reading is

dashed out

•

Wireless model - check reception. See Reception

Problems below.

•

Cabled model - cable may be faulty.

If these steps do not reveal the problem, the anemometer may

be faulty. Call technical support.

Wind direction always says

north

Usually a problem in the ISS, either with the transmitter or

anemometer cable. See the ISS manual for troubleshooting in-

formation.

Chill

Wind chill reading seems

too high or too low

Check calibration numbers for temperature. Wind chill depends

on temperature and wind speed. Make sure they’re working.

Heat

Heat Index reading seems

too high or too low

Check calibration numbers for temperature. The heat index

depends on temperature and outside humidity. Make sure the

sensors are working.

Rain

No rain readings

Make sure cable-tie is removed from inside the rain collector.

See the ISS manual.

UV/Solar

Readings are too high

Can be caused by high thin cirrus clouds.

ime

Incorrect times for sunrise

and sunset

Check your latitude, longitude, time zone, date and daylight

saving time settings. Sunrise and sunset times are calculated

from the console using all of these settings.

ABLE

4-1: T

ROUBLESHOOTING

UIDE

Problem

Solution

Содержание 6152





























































Результаты поиска

Содержание 6152

Отзывы:

DAVIS 6152, Руководство пользователя, Страница: 41 / 60

Результаты поиска

Содержание 6152

Отзывы: