DAVIS 6152 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 60

DAVIS 6152 Скачать руководство пользователя страница 14

Console Location

10

Wall Mounting

The console mounts to the wall using two keyholes located on the back of the case.
To mount the console on a wall:
1. Use a ruler to mark two mounting hole positions on the wall 8 inches (203 mm)

apart.

This is a representation for the mounting hole positions. This template is not true to size

.

If installing a cabled Vantage Pro2 console with sensor cable running inside the
wall, mount the console over an empty switch box.

2. Use a drill and a 3/32 or 7/64''(2.5 mm) drill bit to drill two pilot holes for the

screws.

3. Using a screwdriver, drive the two #6 x 1'' pan head self-threading screws into

the wall. Leave at least 1/8'' (3 mm) between the wall and the heads of the
screws.

4. If the kickstand has been pulled out from the case, push it back into its upright

and locked position.

5. Guide the two keyholes on the back of the console over the two screws.

Drill two 3/32" or 7/64" (2.4 to 2.8mm) holes
8" (203mm) apart for the #6 x 1" mounting screws.

8" (203mm)

«
...
12
13
14
15
16
...
»

Содержание 6152





























































Отзывы:

Нет отзывов