DAVIS 6152 Скачать руководство пользователя страница 25

Страница: 25 / 60

Selecting Units of Measure

Repeating these steps cycles through the units available for barometric
pressure: millibars, millimeters, inches, and hectoPascals.

Wind Speed and Direction

1. Press WIND to select wind speed.
2. Wind speed may be displayed in miles per hour (m.p.h.),

kilometers per hour (km/h), meters per second (m/s), and knots
(knots). The 10 minute average wind speed will be displayed in the ticker.

A solid arrow within the compass rose indicates the current wind direction.
Arrow caps indicate up to six different 10-minute dominant wind directions to

provide a history of the dominant wind directions for the past hour.

3. Press WIND a second time to display the wind

direction in degrees instead of the wind speed. When
displayed in degrees, Due North displays as 360

Each additional WIND

key press toggles the display

between wind speed and wind direction in degrees.

Note:

If your anemometer arm is not pointing true north, you should recalibrate the wind
direction reading on your console. See “Calibrate Wind Direction Reading” on
page 27 for more information.

BAROMETER

Displaying Units: Barometric Pressure Units: millibars (mb), millimeters (mm) and

Vertical Scale: X10

WIND

RAIN

YEAR

TEMP OUT

HUM IN

HUM OUT

DAILY RAIN

TEMP IN

hPa

BAROMETER

STATION NO.1

MPH

Last 24 hrs

Every1

TEMP IN

TEMP OUT

HEAT INDEX

WIND

MPH

Wind Direction, Outside and Inside Temperature

WIND

360˚ N

45˚ NE

90˚ E

135˚ SE

180˚ S

225˚ SW

270˚ W

315˚ NW

Содержание 6152





























































Результаты поиска

Содержание 6152

Отзывы:

DAVIS 6152, Руководство пользователя, Страница: 25 / 60

Результаты поиска

Содержание 6152

Отзывы: