DAVIS 6152 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 60

DAVIS 6152 Скачать руководство пользователя страница 43

Console Diagnostic Mode

39

Diagnostic Screen Commands

• Press and hold TEMP, then press HUM to display the Statistical Diagnostic

screen.

• Press the > key to display signal statistics for the next installed transmitter ID.
• Press 2ND and then press CHILL to toggle between the Statistical and

Reception Diagnostic screens.

• A degree (

°

) sign displays in right corner of value 1 of the Reception

Diagnostic screen (screen 2) to differentiate which screen is currently
displayed.

• Press DONE to exit the diagnostic screen.

Screen 1: Statistical Diagnostic Screen

The Statistical Diagnostic displays information about how data is being received
from the weather station to the console. The information that is displayed in this
screen includes:

Screen 1: Statistical Diagnostics Screen

Note:

All values with a * mark the value as being for Davis Instruments Internal use. All values with a

‡

mark values that are the same on both the Statistical and Reception Diagnostic screens.

1.

Time of day or number of times the anemometer switch was seen closed

*

.

The switch closes once each revolution of the anemometer wind cups. Press
WIND to toggle between these two values.

2.

Date or the number of times the anemometer switch was seen open

*

. Press

WIND to toggle between these two values.

Note:

The time and date displays can be toggled in both statistical and reception diagnostic screens.

3.

Number of packets containing CRC errors received. The system runs a CRC
check on data packets. Any data packets that don’t pass this check are

Vertical Scale: 1 0

STATION NO. 5

am

Last 24

days

day

Every 1

«
...
41
42
43
44
45
...
»

Содержание 6152





























































Отзывы:

Нет отзывов