manualshive.com logo in svg
background image

5

Installation of the ProMaster Premium VSD400 Pump:

Location

The pump should be located as close to the water as practicable and mounted 

on a firm base in a well drained position, high enough to prevent any flooding. It is 

the installer’s/owner’s responsibility to locate the pump such that the nameplate 

can be easily read and the pump can be readily accessed for service.

Weather Protection

It is recommended that the pump is protected from the weather. Enclosures 

should be ventilated to prevent condensation build-up.

Power Connection

Davey ProMaster is suitable for connection to a nominal 240 volt 50Hz power 

supply and is equipped with a flex and 3 pin plug. If a power outlet is not 

available within 3 metres of the pump, a 3 pin power point in a safe, dry place 

may need to be provided by an electrician. Extension cords are unsafe around 

pools - and should be avoided. If the supply cord of this product is damaged it 

must be replaced by the dealer or manufacturer, with genuine Davey spares.
This ProMaster pool pump incorporates motor overload detection designed to 

protect the motor from overheating. If the motor gets too hot during operation, 

its operating speed will reduce to bring it within a acceptable operating 

temperature and then will speed up to the originally set speed.
To reset the motor, switch the power off for 30 seconds, and then return the 

power from the mains switch.

'DYH\:DWHU3URGXFWVUHFRPPHQGVWKDWDOOLQVWDOODWLRQVDUH¿WWHG

with earth leakage or residual current protection devices.

CAUTION: In the interest of safety, we advise that all brands and 

types of pool pumps must be installed in accordance with AS3000 

wiring rules or equivalent.

,IWKHSXPSDQG¿OWHUDUHORFDWHGEHORZSRROZDWHUOHYHOLWLV

QHFHVVDU\WR¿WLVRODWLQJYDOYHVLQWKHSLSHEHWZHHQWKHSXPSDQG

VNLPPHUER[DQGLQUHWXUQSLSHIURPWKH¿OWHUWRWKHSRRO
7KH¿WWLQJVRQWKLVSURGXFWDUHFRQVWUXFWHGRI$%66RPH39&

MRLQWLQJFRPSRXQGVDUHLQFRPSDWLEOHZLWK$%6&KHFNFRPSRXQG

suitability before use.

WARNING! Ensure that an electrical isolation switch is located with 

easy access so that the pump can be switched off in an emergency.

Содержание PM400PV





















Отзывы: