background image

15

Operating your Suction Pool Cleaner

Before installing or purchasing a pool cleaner for use with your ProMaster 

pool pump, it is important to know the minimum flow rates required for it to 

operate effectively.

To operate a suction pool cleaner with your  

ProMaster Premium VSD400 pump:

1. Activate the High Flow setting (10) and allow the pump to fully prime by 

running for around 2 minutes. You will know the pump is primed when you 

can see a strong flow of water through the clear leaf basket lid.

2. When all air is expelled from the leaf basket, connect the pool cleaner 

hose firmly into the skimmer plate or dedicated wall suction.

3. Select the speed setting that enables best performance from your suction 

pool cleaner. Speed 3 to 7 should be ample for most cleaners, however if 

the cleaner requires better performance, select speeds 7 to 10. A Davey 

PoolSweepa suction pool cleaner is recommended to run between speeds 

2 to 3.

4. The cleaner should only be connected for as long as is required to clean 

the surface of your pool. When cleaning is complete, disconnect the 

cleaner and remove the skimmer plate from the skimmer box.

127(7RJHWRSWLPXPHQHUJ\HI¿FLHQF\IURP\RXU3UR0DVWHU

 

DO NOT keep 

the suction pool cleaner connected when cleaning is not required.

5. Reactivate the most efficient speed setting for daily filtration. Speeds 1 to 4 

is recommended.

0DLQWHQDQFH(PSW\LQJWKH6WUDLQHU%DVNHW

The strainer basket should be inspected frequently through the transparent 

lid and emptied when a build up of rubbish is evident. The directions below 

should be followed.
1. Switch off pump.
2. Unscrew the strainer basket lid anti-clockwise and remove.
3. Remove the strainer basket by lifting upwards from its housing.
4. Empty the trapped refuse from the basket. Hose out with water if necessary.

NOTE: NEVER knock the plastic basket on a hard surface as it will cause damage.

Содержание PM400PV





















Отзывы: