29
D
EMERGENCY STOP:
2 EMERGENCY STOP Systems
EMERGENCY STOP button and
EMERGENCY STOP safety rope
Running surface:
1.5 x 0.5m foldable
Inclination setting:
adjustable from 0 % to 12% in 0.5 % in
crements
Load precision:
Conform to DIN EN 957 1/-6 Class SA/HA
Speed:
adjustable from 0.8 to 20 km/h in 0.5 km/h
increments
Drive:
1.9 kW direct current motor
Displays:
4 graphical windows
Heart rate measurement:
using the ear clip
measuring range 50 to 199 beats/min.;
Telemetric using the Cardio sensor chest
belt measuring range 50 to 215 beats/min.
Alarm signals:
Acoustic and optical
Weight:
approx. 150 kg
Installed dimensions:
L 205 cm, W 86, and H 136
Folded dimensions:
L 106 cm, W 86, and H 190
Power supply:
230 V alternating current, 50 Hz, 2000W
Safety class:
I
Technical Safety Recommendations:
Compare the supply voltage indicated on the nameplate located on the
housing with your local supply voltage prior to plugging the power cord to the
power supply. Please contact you dealer if the values are not the same.
The device is completely disconnected from the power supply by pulling out
the power cord, therefore it should always be plugged into an easily acces-
sible socket.
Liability
The manufacturer will not be held liable if the treadmill is not used in compli-
ance with the provided instructions and recommendations and if the prescrip-
tions are ignored.
Maintenance and technical safety controls
Before every maintenance operation the device must be
completely disconnected from the power supply by pulling
out the power plug. The treadmill must also be turned OFF
for safety reasons.
Preventive maintenance
A regular maintenance schedule helps prevent failures and problems before
they appear and guarantees an optimal functional state for the device. The
manufacturer recommends a yearly maintenance cycle.
Before the device is turned ON, you must always check that the power cord,
power plug, wall socket and power supply are faultless.
Immediate maintenance operations
Immediate maintenance operations are needed when:
-
any liquid penetrated the device
-
the device was exposed to a heavy mechanical shock (e.g. impact,
strong pull on the power cord or other connection cables).
-
the cables and/or connector are damaged
-
the cover elements went off
-
the rubber elements are cracked (particularly the running belt and
the drive belt) the running belt is not centred.
Lateral treadways: make sure they are not slippery
Every treadmill ergometer is equipped on both sides of the running surface
with a non-slippery treadway. These surfaces guarantee a safe stand in emer-
gency situations. Please check the non-slip surface at regular intervals and
replace them immediately when they are worn out.
Fastening Screws
All the fastening screws must be tightened up from time to time. We recom-
mend tightening them at least after the first 50 km and then once every 500
km.
!
Noises
The lubricant applied by the manufacturer between the running belt and its
base plate must be renewed if the device is used frequently. At the very latest
lubricate the running belt when you hear dry rubbing sound while running.
Cleaning
For safety reasons you must switch the treadmill off and pull out the power
cord before you proceed with cleaning or disinfecting the treadmill and every
time you open the cover or access its components. Chemical products
needed for the operation or care of the treadmill must be kept, prepared and
presented exclusively in the designated container because of the risks of
confusion.
Clean the outside surfaces with a wetted soft cloth. Do not use any strong or
corrosive cleaning solution, or one containing solvents, (e.g., alcohol, stain
remover, etc).
Care should be taken to wipe out sweat drops after training (sweat attacks
paint and plastic parts). Damage caused by sweat is not covered by the
warranty. You can clean the coating of the handrails with a mild detergent,
applying appropriate caution.
These are wear parts and are not covered by the warranty.
Clean the drinking bottle after use out of hygienic reasons. We also recom-
mend cleaning the bottle before filling it with various drinks, particularly if not
used regularly.
About the V-belt
The driving surfaces of the drive pulley and the V-belt pulley are covered
with a rubber layer by the manufacturer.
This favours the development of an optimal fitting of the V-belt into the groo
-
ves of the driving pulley during the first 500 to 1000 kilometres.
During the first 500 to 1000 km the belt will loose some excess rubber, which
will appear in the form of black powder deposits. You can remove these depo-
sits using a small brush or a vacuum cleaner.
V-belts are wear parts and are not covered by the warranty.
Specifications
Maintenance
GB
Содержание ergo_run classic
Страница 1: ...User Manual ergo run classic ...
