manualshive.com logo in svg

Datex-Ohmeda S/5 M-ESTPR, Техническое описание слота

Поделиться
Скачать
Datex-Ohmeda S/5 M-ESTPR Скачать руководство пользователя страница 66

Datex-Ohmeda S/5 monitors

Document No. 800 1008-2

60

5.1.6

 

NIBP pneumatics menu

Start Pump/Stop Pump

A manual control for the pump. The selection changes to 

Stop Pump

 when the pump turns on.

Open Exh1/Close Exh1

A manual control for the exhaust valve 1. The selection changes to Close Exh1 when the valve is

opened.

Open Exh2/Close Exh2

A manual control for the exhaust valve 2. The selection changes to 

Close Exh2

 when the valve is

opened.

Set Valve

With 

Set Valve

, the opening of the pulse valve is adjusted between 0 and 255 (0 for fully closed

and 255 for fully open). First push the ComWheel, then turn it to adjust the value on screen and

finally push to set the value.

Reset Clock

Reset Clock

 will zero the time on the display.

Pneumatics Data field

See NIBP service menu in chapter 

5.1 

for information on general items 

Pressure, Zero, Protect

handle, Calibr. prot., +15 V power, AD0

 to 

AD7

 as well as 

Timeouts

 etc.

Pump, Exh1 Valve

, and 

Exh2 Valve

 show their states.

Pulse Valve

 shows how much the valve is opened (0 to 255) during Valve Setting.

Interval 20 mmHg -> 185 mmHg Checking

Select the 

Start pump

 at different combinations of the valves open/closed and push the

ComWheel. The module counts the time it takes for the pressure to go up from 20 mmHg to 185

mmHg and displays it. When all the valves are closed, the pump should be able to pump the

pressure in about 1 to 4 seconds into an adult cuff wrapped around a pipe. The pump does not

stop without selecting the 

Stop Pump

 by pushing the ComWheel.

Watchdog BEEP

Connect manometer to the front panel and pump pressure into the module. When the AD5 value

Содержание S/5 M-ESTPR

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды