manualshive.com logo in svg

Datex-Ohmeda S/5 M-ESTPR, Техническое описание слота

Поделиться
Скачать
Datex-Ohmeda S/5 M-ESTPR Скачать руководство пользователя страница 62

Datex-Ohmeda S/5 monitors

Document No. 800 1008-2

56

5.1.2

 

NIBP calibration menu

Active Leak Test

Wrap an adult cuff around a pipe and connect the cuff to the module. Select the active leak test
(ON). The module automatically pumps a pressure of 260 mmHg into the cuff. Wait for several

seconds until the pressure stabilizes. Then check that the pressure reading does not drop more

than 5 mmHg per minute. If it does, leaking point(s) should be detected and fixed. Cancel the test

by selecting Active leak test OFF.

Calibration Check

After the calibration check is selected (ON), manually pump pressure into the module and make

sure that the same pressure values are shown both on the display and on manometer. Pressure of

both pressure channels B1 and B2 are shown. Note that if the display shows +2 mmHg at zero

pressure and if you 200 mmHg into the module, the display should show +202 mmHg.

Protection

Software calibration protection (ON/OFF). Select OFF when calibrating. Protection can be set to ON
or OFF only when the toggle switch at the bottom of the module is set to the right.

Calibration

Calibration selection is available only when protection is OFF.
NIBP calibration can be performed in the NIBP Service menu as follows:
NOTE: Both channels B1 and B2 must be calibrated simultaneously.
1.

 

If 

Protection

 is ON change it to OFF by first turning the toggle switch to the right at the

bottom of the module, which enables the 

Protection

 selection. Then turn the toggle switch

to the left to enable 

Calibration

.

NOTE : Do not disconnect the module from the frame when turning the switch. The module must be

in the frame during the whole procedure.
NOTE: When the switch is at the right, the NIBP field shows an error message ‘Calibration switch

on!’.
NOTE: When calibration is enabled, a message ‘Calibration not protected’ appears.
2.

 

For proper zeroing to take place, remove the hose from the front panel connector. Select

Calibration

 and push the ComWheel. Messages ‘Zeroing’ and ‘Zeroed’ will appear in the

NIBP message field. After this a pressure bar will appear beside the menu.

Содержание S/5 M-ESTPR

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды