Datakom DKG-519 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 55

background image

DKG-519 User Manual V-27

(14.04.2011)

- 23 -

6.18 Exerciser

The unit offers automatic exerciser operation. The exercise operation may be done on a daily,

weekly or monthly basis.

The start day and time of the exercise is programmable as well as its duration. The exercise

may be done with or without load following programming.

Program parameters related to the exerciser are:

Exercise start day and hour

Exercise duration

Exercise off_load/on_load

Exerciser Period (Daily / Weekly / Monthly)

Please refer to the programming section for a more detailed description of the above

parameters.

When the start day and hour of exercise has come, the unit will automatically switch to either

TEST

or

LOAD TEST

mode. The engine will run and if the on_load exercise is selected then the load

will be transferred to the genset.

If a mains failure occurs during the off-load exercise, the load will not be transferred to the

genset unless the

Emergency Backup Operation

is allowed by setting the related program

parameter to 1. Thus it is highly recommended that the Emergency Backup mode enabled with off-
load exerciser.

At the end of the exercise duration, the unit will switch back to the initial mode of operation.

If any of the mode selection keys are pressed during exercise, then the exercise will be

terminated.

«
...
21
22
23
24
25
...
»

Содержание DKG-519
























































Отзывы:

Нет отзывов

Похожие инструкции для DKG-519

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: rada Страницы: 16

Бренд: Danfoss Страницы: 24

Бренд: National Instruments Страницы: 40

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 22

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

Бренд: u-blox Страницы: 28

Бренд: VAT Страницы: 26

Бренд: Panasonic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды