Datakom DKG-519 Скачать руководство пользователя страница 15

Страница: 15 / 55

DKG-519 User Manual V-27

(14.04.2011)

- 15 -

6.3 Engine Heating Operation

Especially on engines without a body heater, or with a failing one, it may be desired that the

genset should not take the load before reaching a suitable temperature. The unit offers 2 different
ways of engine heating.

1. Timer controlled heating:

This operation mode is selected when the

Engine Heating Method

parameter is set to

. In this

mode, the engine will run during parameter

Engine Heating Timer

, and then the generator contactor

will be activated.

2. Timer and temperature controlled heating:

This operation mode is selected when the

Engine Heating Method

parameter is set to

. In this

mode, at first the engine will run during parameter

Engine Heating Timer

, then it will continue to run

until the measured coolant temperature reaches the limit defined in parameter

Engine Heating

Temperature

. When the requested temperature is reached, the generator contactor will be operated.

This operation mode may be used as a backup to the engine body heater. If the engine body is warm
the heating will be skipped.

6.4 Engine Idle Speed Operation

It may be required that the engine runs at the idle speed for a programmed duration for engine

heating. The idle operation duration is adjusted with the parameter

Idle Speed Timer

. The idle speed

will be set by the governor control unit of the engine.

Any of the spare relay outputs may be assigned as

IDLE output

using

Relay Definition

program parameters. Also relays on an extension module may be assigned to this function.

The Idle speed operation is performed both in engine start-up and cool-down sequences.

Speed and voltage protections are disabled during idle speed operation.

6.5 Engine Block Heater

The unit is able to provide a relay output in order to drive the block heater resistor.

The temperature reference is the coolant temperature measured from the the analog sender

input.

The block heater relay function may be assigned to spare relays using

Relay Definition

program parameters. Also relays on an extension module may be assigned to this function.

The engine body temperature limit is adjusted using the parameter

Engine Heating

Temperature

. The same parameter is used for engine heating operation.

The relay will become active if the body temperature falls to 4 degrees below the limit set by

Engine Heating Temperature

. It turns off when the body temperature exceeds

Engine Heating

Temperature

Содержание DKG-519
























































Результаты поиска

Содержание DKG-519

Отзывы:

Похожие инструкции для DKG-519

Бренды по названию

Популярные бренды

Datakom DKG-519, Руководство пользователя

Результаты поиска

Содержание DKG-519

Отзывы:

Похожие инструкции для DKG-519

Бренды по названию

Популярные бренды