manualshive.com logo in svg

Datakom DKG-255, Руководство пользователя

Поделиться
Скачать
Datakom DKG-255 Скачать руководство пользователя страница 2

DKG-255 User Manual                                                                           Firmware V-1.0                     

 

 

                                                                                                              

 

 

   
Any unauthorized use or copying of the contents or any part of this document is prohibited. 
This applies in particular to trademarks, model denominations, part numbers and drawings. 
 
 

 

 
This document describes minimum requirements and necessary steps for the successful installation of 
the DKG-255 unit. 
Follow carefully advices given in the document. These are often good practices for the installation of 
digital speed control unit which reduce future issues. 
For all technical queries please contact Datakom at below e-mail address: 

[email protected] 
 

 

If additional information to this manual is required, please contact the manufacturer directly at below e-
mail address: 

[email protected] 

Please provide following information in order to get answers to any question: 

- Device model name (see the back panel of the unit), 
- Complete serial number (see the back panel of the unit), 
- Firmware version (read from the display screen), 
- Measuring-circuit voltage and power supply voltage, 
- Precise description of the query. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

QUERRIES

 

 

ABOUT THIS DOCUMENT

 

 

COPYRIGHT NOTICE

 

 

Содержание DKG-255



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды