DataDirect Networks EF3015 Скачать руководство пользователя | Manualshive

Страница: 51 / 59

background image

Environmental Requirements & Specifications

E F 3 0 1 5 S e t u p G u i d e ( R e v A )

51

B.3

Management Host Requirements

A local management host with at least one serial port connection is recommended for the
initial installation and configuration of a controller enclosure. After you configure one or
both of the controller modules with an IP address, you then use a remote management host
on an Ethernet network to manage and monitor.

NOTE :

Connections to this device must be made with shielded cables with

metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and
Regulations.

B.4

Physical Requirements

The floor space at the installation site must be strong enough to support the combined
weight of the rack, controller enclosures, drive enclosures, and any additional equipment.
The site also requires sufficient space for installation, operation, and servicing the
enclosures, together with sufficient ventilation to allow a free flow of air to all enclosures.

The table below shows the enclosure dimensions and weights. Enclosure designators are
described below. Enclosure weights assume the following configuration characteristics:

• 2U12 enclosure (LFF)

- “2U12” denotes the 3.5” 12-drive enclosure (with controller or expansion modules)

- 2U12 chassis is equipped with a disk in each disk drive slot

• Two controller or expansion modules per enclosure

• Two power supplies per enclosure

.

Specifications

Rackmount

2U Height (y-axis):

3.45 inches (8.7 cm)

Width (x-axis):
•

Chassis-only

•

Chassis with bezel ear caps

17.6 inches (44.7 cm)
18.9 inches (47.9 cm)

Depth (z-axis):

12-drive enclosure (2U12):
•

Back of chassis ear to controller latch

•

Front of chassis ear to back of cable bend

23.7 inches (60.2 cm)
26.4 inches (67.0 cm)

12-drive controller enclosure (2U12)
•

Chassis with FRUs (no disks)

a,b

•

Chassis with FRUs (including disks)

a,c

a.

Weights shown are nominal, and subject to variances.

b.

Weights may vary due to different power supplies, IOMs, and differing
calibrations between scales.

c.

Weights may vary due to actual number and type of disk drives (SAS, SATA,
SSD) installed.

22.0 lb (9.9 kg) [chassis]
47.0 lb (21.3 kg)
68.0 lb (30.8 kg)

«
...
49
50
51
52
53
...
»

Содержание EF3015




























































Отзывы:

Нет отзывов

Похожие инструкции для EF3015

Бренд: Macpower & Tytech Страницы: 14

Бренд: Kramer Страницы: 2

Бренд: Black Box Страницы: 11

Hoffman NEMA Series

Бренд: Pentair Страницы: 8

OptiX OSN 9800 U32 Enhanced Subrack V100

Бренд: Huawei Страницы: 78

Бренд: AJA Страницы: 12

Бренд: FSP Technology Страницы: 20

Бренд: Pulsar Страницы: 4

SmartRack SRWF5U

Бренд: Tripp Lite Страницы: 8

SmartRack SRW12UHD

Бренд: Tripp Lite Страницы: 24

SmartRack SRW12U13

Бренд: Tripp Lite Страницы: 24

ToughTech Duo C

Бренд: CRU Страницы: 8

Бренд: Banner Страницы: 22

Бренд: TSI Instruments Страницы: 70

Бренд: MAG Страницы: 53

Бренд: Vantec Страницы: 2

Бренд: Icy Dock Страницы: 64

Thunderbolt IB-3101-TB3

Бренд: Icy Box Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды