DataDirect Networks EF3015 Скачать руководство пользователя страница 4

Страница: 4 / 59

E F 3 0 1 5 S e t u p G u i d e ( R e v A )

Preface

This guide provides information about the EF3015 Fibre Channel Controller Enclosure:

The EF3015 isMIL-STD-compliant and supports large form factor (LFF 12-disk) drive
enclosures — using either AC or DC power supplies.

NOTE :

See

"The EF3015 System Components"

for details regarding enclosure

components.

Intended audience

This guide is intended for use by system administrators and technicians who are
experienced with the following:

• Direct attach storage (DAS) or storage area network (SAN) management

• Network administration

• Network installation

• Storage system installation and configuration

Prerequisites

Prerequisites for installing and configuring this product include familiarity with:

• Servers and computer networks

• Fibre Channel (FC), Serial Attached SCSI (SAS), Internet SCSI (iSCSI), and Ethernet

protocols

Related Documentation

• EF3015 Command Line User Interface (CLUI) Command Reference

• EF3015 Quick Start Guide

• EF3015 Rackmount Bracket Kit Installation Instructions

• EF3015 RAIDar User Guide

Содержание EF3015




























































Результаты поиска

Содержание EF3015

Отзывы:

Бренды по названию

Популярные бренды

DataDirect Networks EF3015, Руководство по установке

Результаты поиска

Содержание EF3015

Отзывы:

Бренды по названию

Популярные бренды