DataDirect Networks EF3015 Скачать руководство пользователя | Manualshive

Страница: 14 / 59

background image

Installation

E F 3 0 1 5 S e t u p G u i d e ( R e v A )

14

- Use RAIDar to shut down both controllers, as described in the online help and the

EF3015 RAIDar User Guide.

- Proceed to Step

- Use the command line interface (CLI) to shut down both controllers, as described in

the EF3015 CLI Reference Guide.

3.

Disconnect the power cord’s male plug from the power source.

4.

Disconnect the power cord’s female plug from the power cord connector on the PSU.

2.4

DC and AC PSUs with power switch

Power
switch

Power
cable
connect

Power
switch

Power
cord
connect

DC Power Supply Unit

Legacy AC Power Supply Unit

Figure 5. DC and AC PSUs with Power Switch

DC and legacy AC power supplies — each equipped with a power switch — are shown in

2.4.1

Power Cords

IMPORTANT :

See Appendix

B "Environmental Requirements &

Specifications"

for additional information.

«
...
12
13
14
15
16
...
»

Содержание EF3015




























































Отзывы:

Нет отзывов

Похожие инструкции для EF3015

Бренд: Stardom Страницы: 14

Бренд: Jaycar Electronics Страницы: 16

Бренд: Clare Controls Страницы: 2

93PM IAC-T Series

Бренд: Eaton Страницы: 98

Performance TX635

Бренд: Antec Страницы: 8

Бренд: PPM Страницы: 20

Бренд: Charles Страницы: 13

Бренд: Aerocool Страницы: 2

ORMAZABAL basic pfu Series

Бренд: Velatia Страницы: 32

Бренд: Kraun Страницы: 10

Бренд: SilverStone Страницы: 36

Бренд: AFL Страницы: 14

Бренд: Gallien-Krueger Страницы: 3

Бренд: VERITAS Страницы: 12

Бренд: Natec Страницы: 12

SmartRack SRW9U

Бренд: Tripp Lite Страницы: 3

SmartRack SR42UBEIS

Бренд: Tripp Lite Страницы: 13

Бренд: Nakamichi Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды