DataCard SP75 Plus Скачать руководство пользователя страница 60

Страница: 60 / 136

Page 55

DM-00767 Duplex Jam

The card is lost in the duplex module.

Possible Cause 1:

A card is jammed in or near the duplex unit.

Solution 1a:

Open the back door of the printer (1). Release any cards stuck

in the module (2). Make sure that the duplex mechanism can move freely in
the direction shown (3).

Solution 1b:

If the card is stuck between the upper and lower duplex units,

remove the card from the printer. You might see a “PR 01706” message after
removing the card. Clear the message to continue.

Possible Cause 2:

The rollers in the duplex mechanism are dirty.

Solution 2:

Run a printer cleaning card, and then clean the printer rollers

including the duplex module rollers.

If you cannot fix the problem,

contact your service provider for assistance.

Related Topics:

"Cleaning the printer" on page 21

Содержание SP75 Plus









































































































































Результаты поиска

Содержание SP75 Plus

Отзывы:

Похожие инструкции для SP75 Plus

Бренды по названию

Популярные бренды

DataCard SP75 Plus, Руководство пользователя

Результаты поиска

Содержание SP75 Plus

Отзывы:

Похожие инструкции для SP75 Plus

Бренды по названию

Популярные бренды