DataCard SP75 Plus Скачать руководство пользователя страница 112

Страница: 112 / 136

Page 107

PR-01705, PR-01706 Card Jam

The card is stuck or lost in the printer.

Possible Cause:

The card is stuck in the print area.

Solution:

Release the card so it can move.

Open the top cover of the printer.

Remove the ribbon cartridge.

Locate the card inside the print area. The card might be stuck near the
cleaning roller, the printhead, near the optional magnetic stripe or smart
card module, or at the end of the card track.

Turn the Manual Advance Knob to move the card.

If needed, grasp an end of the card and pull to remove the card.

Replace the ribbon cartridge and close the printer cover.

Press the Ready key to clear the printer.

Tips for success:

•

If the print ribbon is torn, fix the print ribbon.

•

If the printer picks two cards, fan cards before loading the input hopper.

Содержание SP75 Plus









































































































































Результаты поиска

Содержание SP75 Plus

Отзывы:

Похожие инструкции для SP75 Plus

Бренды по названию

Популярные бренды

DataCard SP75 Plus, Руководство пользователя

Результаты поиска

Содержание SP75 Plus

Отзывы:

Похожие инструкции для SP75 Plus

Бренды по названию

Популярные бренды