DataCard SD Series страница 51 Скачать руководство пользователя

Страница: 51 / 106

SD Series Card Printers User’s Guide

USB Installation Troubleshooting

Problem

Solution

The cable is loose.

Reconnect the USB cable to the ports on the PC and

the printer. Power the printer off, and then back on. If

the PC and printer still do not communicate, restart

the PC.

The data cable is

damaged or frayed.

Power off the printer. Replace the cable if you have

a spare. Contact your service provider to order a

new data cable.

The system has a

temporary

communication

problem.

Check for the following:

•

USB extension cables can cause

communication problems. The recommended

USB cable is 6-ft. (2 meters) long. Make sure that

the cable is rated for USB 2.0 data transmission.

•

If you are using a USB hub, a self-powered hub

is recommended.

The PC USB port does

not communicate with

the printer USB port.

Power management on the PC has shut down USB

communication.
Open the Device Manager and the list of USB

devices. Disable shutdown for each hub in the list.

Restart the PC to make the changes take effect, if

necessary.
Hibernation on a laptop PC requires several moments

to enable USB communication. Unplug the USB

printer port and then connect it again.
Replace the PC port or the PC. Contact your PC or

port vendor if you need assistance.

Содержание SD Series











































































































Результаты поиска

Содержание SD Series

Отзывы:

Похожие инструкции для SD Series

Бренды по названию

Популярные бренды

DataCard SD Series, Руководство пользователя

Результаты поиска

Содержание SD Series

Отзывы:

Похожие инструкции для SD Series

Бренды по названию

Популярные бренды