background image

6

INTRODUCTION

Thank you for choosing an E11EVEN Sound product for your application. Please spend a little 
time reading through this manual so that you can obtain the best possible performance from 
the unit. All E11EVEN products are carefully designed and engineered for cutting-edge 
performance and world-class reliability. If you would like further information about this, or 
any other E11EVEN product, please do not hesitate to contact us. 

UNPACKING THE UNIT  

After unpacking, please check the unit carefully for any damage. If any is found, immediately 
notify the carrier concerned - you, the consignee, must instigate any claim. Please retain all 
packaging, in case of future re-shipment. 

INSTALLATION

-

Electrical Considerations:

The 

D10

D20

 

and D100 

device

s

 ha

ve

 been manufactured to comply with your local power 

supply requirements, but before connecting the unit to the supply, ensure that the voltage 
(printed on the rear panel) is correct, and that a main fuse of the correct type and rating has 
been fitted. Make sure power outlets conform to the power requirements listed on the back 
of the unit. Damage caused by connecting to incorrect AC voltage is not covered by the 
warranty.

-

Mechanical Considerations:

To ensure that this equipment performs to specification, it should be mounted in a suitable 
rack or enclosure. When mounting the unit in a rack or enclosure, ensure that there is 
adequate ventilation. The cooling fan sucks cool air in through the right side and blows warm 
air out of the left side of the unit through the ventilating grills. Take care when mounting 
other equipment in the same rack.

-

Operation:

Read all documentation before operating your equipment and retain all documentation for 
future reference. Do not spill water or other liquids into or on the unit and do not operate the 
unit while standing in liquid. Do not block the fan intake or operate the unit in an 
environment that could impede the free flow of air around the unit. If the unit is used in an 
extremely dusty or smoky environment, it should be cleaned of any collected debris at 
regular intervals.

E11EVEN SOUND \ 

D series amplifiers 

User’s Manual

Содержание E11EVEN SOUND D Series
















Отзывы: