background image

How to Install and Operate
the LXA300 Amplifier

®

Contents

 Technical Assistance

For technical assistance with the operation or installation
of the LXA300, call 1-800-323-0221.

Welcome!
What you're holding in your hands is no ordinary
owner's manual. We've tried to make the instructions
in this book clear and easy to follow.
For your Jensen amplifier to work right, it must be
installed correctly. This manual will show you how to
install your new amplifier like a pro. It's a good idea to
read all of these instructions before you begin the
installation. Most installations are straightforward and
can be handled by a do-it-yourselfer with the right
tools, patience, and the ability to follow instructions.
But, do-it-yourself installation isn't for everyone. If you
still don't feel confident after reading this book,
consider turning the installation job over to someone
better suited to it.

Warranty Service
If your Jensen amplifier should ever require service,
you will need to have the original dated receipt. If you
ever need to return the unit for any reason, always
include the receipt with the product.

Features

........................................

2

Installation

...................................

2

Before You Begin
Installation ..................................... 2

Amplifier Location .......................... 2
Disconnect Battery ........................ 2

• Amplifier Installation Kit ............. 2

Supplies and Tools
Needed .......................................... 3
Routing Wires ................................ 3

• Bigger is Better .......................... 3

Wiring

.............................................

4

Power and Outputs ........................ 4
Power Terminal (BATT +12V) ........ 4

Ground Terminal (GND) ................. 4
Remote Terminal (RMT +12V) ....... 4
Fuses ............................................. 4
Inputs and Controls ....................... 5

Input Wiring .................................... 5
Pass Output ................................... 5
Power Light .................................... 5
Protect Light .................................. 5

Input Level Control ........................ 6
Bass Boost ..................................... 6
Crossover ...................................... 6
Speaker Wiring .............................. 7

Testing

..........................................

9

Reconnect Battery ......................... 9

Test Power Wiring .......................... 9
Test Speaker Connections ............ 9

• Dealing with Alternator

Noise .......................................... 9

• Installing in Trunk ..................... 10
• Crimp Connections .................. 10
• Securing Wires ........................ 10
• Speaker and

Power Wires ............................ 10

Troubleshooting

.......................

11

Specifications
and Warranty

.............................

12

50

250

HPF

ON

OFF

BASS
-BOOST

LEVEL

MIN

MAX

LPF

50

250

®

HPF

LPF

FULL

X-O

VER

PO

WER

HI INPUT

LO

W INPUT

L

R

PR

OTECT

PASS

L

R

Содержание LXA300













Отзывы: