Dantherm CDP 50 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 55

background image

45

EN

Evaporator sensor fail

If evaporator sensor is defect, then “EVAP” code will be shown when pressing UP or DOWN
during screen shows Sensor fail code “SEnS”.
If Evaporator sensor ok, then no “EVAP” code shall be shown.
If no buttons pressed within 10 seconds then screen will show “SEnS” fail again.
It is not possible to enter menu setup to modify set point.

RH/T sensor fail

If RH/T sensor is defect, then “rh°t” code will be shown when pressing UP or DOWN during

screen shows Sensor fail code “SEnS”.
If RH/T sensor ok, then no “rh°t” code shall be shown.
If no buttons pressed within 10 seconds then screen will show “SEnS” fail again.
It is not possible to enter menu setup to modify set point.

Low pressure fail

Dehumidifier stopped because of Low Pressure detection.
Fail can not be dismissed from DRC1.
It is not possible to enter menu setup to modify set point.

Alarms continued

Press to see which sensor
is defect.

Press to see which sensor
is defect.

Press to see which sensor
is defect.

Press to see which sensor
is defect.

«
...
43
44
45
46
47
...
»

Содержание CDP 50
























































Отзывы:

Нет отзывов

Похожие инструкции для CDP 50

Бренд: Ebac Страницы: 11

Бренд: Prem-I-Air Страницы: 15

Бренд: Klingenburg Страницы: 52

Бренд: Dantherm Страницы: 192

Бренд: White Rodgers Страницы: 4

Бренд: Dri-Eaz Страницы: 28

Бренд: Lacidoll Страницы: 35

Бренд: Currys Essentials Страницы: 2

Бренд: Impulsion Страницы: 24

Бренд: Nemaxx Страницы: 86

Бренд: INVENTOR Страницы: 12

Бренд: INVENTOR Страницы: 116

Бренд: izzy Страницы: 25

Бренд: camry Страницы: 42

Silhouette DDR583R

Бренд: Danby Страницы: 14

Бренд: Danby Страницы: 16

Premiere DDR60A3GP

Бренд: Danby Страницы: 24

Бренд: Danby Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды