Dantherm CDP 50 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 55

background image

42

EN

Dehumidifying set point

The humidity value and the dehumidifying icon will flash.

The display shows the desired humidity set point.

While flashing, the value can be increased or decreased by pressing Up/Increase or

Down/Decrease button on DRC1.
Press enter to confirm humidity set point and go to next menu page.

Temperature set point

The temperature value and the heating icon will flash.
The value displayed shows the desired temperature set point. While flashing, the value can be

increased or decreased by pressing Up/Increase or Down/Decrease button on the DRC1
Maximum: 34 °C, Minimum: 5 °C. Press enter to confirm new set point and go to next menu page.

User menu
Set points

Decrease with 1 unit

Increase with 1 unit

Navigation between icons

Navigation between icons

Press for 3 sec to enter
user menu setup.
Press to confirm.

Decrease with 1 unit

Increase with 1 unit

Navigation between icons

Navigation between icons

Press for 3 sec to enter
user menu setup.
Press to confirm.

«
...
40
41
42
43
44
...
»

Содержание CDP 50
























































Отзывы:

Нет отзывов

Похожие инструкции для CDP 50

Бренд: VEAB Страницы: 20

Бренд: Morris Страницы: 48

Бренд: Madeira Страницы: 40

Бренд: Yoer Страницы: 36

Бренд: GE Страницы: 24

Бренд: GE Страницы: 2

Appliances ADEW30

Бренд: GE Страницы: 36

Бренд: GE Страницы: 24

Бренд: GE Страницы: 28

Бренд: GE Страницы: 40

Бренд: GE Страницы: 24

Бренд: GE Страницы: 72

Бренд: GE Страницы: 2

Бренд: Crane Страницы: 12

Бренд: Heylo Страницы: 18

Бренд: Ecoair Страницы: 15

Бренд: Ecoair Страницы: 17

Бренд: Fresh Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды