Danfoss VLT HVAC Basic Drive FC 101 Скачать руководство пользователя страница 100

Страница: 100 / 104

Index

Action At Inverter Fault

.................................................................... 66

Active Set-up

......................................................................................... 21

Address

.................................................................................................... 53

Advanced Vector Control

................................................................... 4

AEO

............................................................................................................ 66

Alarm

Log......................................................................................................... 68

Log: Error Code................................................................................. 68

Log: Value........................................................................................... 68

Word..................................................................................................... 73

Word 2.................................................................................................. 73

Words................................................................................................... 83

Alarm/Warning Code List

................................................................ 81

Alarms And Warnings

........................................................................ 81

Analog

Input AI53........................................................................................... 72

Input AI54........................................................................................... 72

Inputs...................................................................................................... 4

Output AO42 [mA]........................................................................... 72

Auto

DC Braking IT..................................................................................... 21

On Key On LCP.................................................................................. 23

Automatic

Motor Adaption (AMA).................................................................. 27

Restart Time....................................................................................... 66

BACnet

BACnet................................................................................................. 55

Device Instance................................................................................. 55

Baud Rate

................................................................................................ 53

Break-away Torque

............................................................................... 5

Broken

Belt Delay............................................................................................ 77

Belt Detection.................................................................................... 77

Belt Function..................................................................................... 77

Belt Torque......................................................................................... 77

Bus

Controlled........................................................................................... 47

Feedback............................................................................................. 56

Changes Made

................................................................................. 9, 18

Closed

Loop...................................................................................................... 24

Loop Set-up Wizard........................................................................... 9

Coast Inverse

......................................................................................... 38

Coasting

Coasting................................................................................................. 4

Select.................................................................................................... 54

Comparator

Operand.............................................................................................. 59

Operator.............................................................................................. 59

Value..................................................................................................... 60

Comparators

......................................................................................... 59

Control

Site......................................................................................................... 53

Timeout Time.................................................................................... 53

Word..................................................................................................... 70

Counter

A............................................................................................................. 72

B.............................................................................................................. 72

Current Limit

......................................................................................... 35

Custom

Readout............................................................................................... 70

Readout Unit...................................................................................... 22

Data Readouts

...................................................................................... 70

Brake Current..................................................................................... 31

Brake Cut In Speed.......................................................................... 31

Braking Time...................................................................................... 31

Hold/Motor Preheat Current........................................................ 31

Link Compensation......................................................................... 67

Default Settings

................................................................................... 87

Definitions

................................................................................................ 4

Digital

Input..................................................................................................... 71

Input 29 Mode................................................................................... 38

Input Function.................................................................................. 38

Input Mode......................................................................................... 38

Inputs................................................................................................... 38

Output.................................................................................................. 72

Display

........................................................................................................ 8

Drive

Bypass.................................................................................................. 79

Identification..................................................................................... 68

E-##* Digital I/O

................................................................................... 38

Electrical Overview

............................................................................... 7

Energy Optimising

.............................................................................. 66

Environment

.......................................................................................... 66

Extended

Status Word........................................................................................ 73

Status Word 2.................................................................................... 73

Status Words...................................................................................... 84

External

Interlock............................................................................................... 38

Reference............................................................................................ 71

Index

VLT

HVAC Basic Drive FC 101 Programming Guide

MG18B302 - Rev. 2013-09-02

Содержание VLT HVAC Basic Drive FC 101









































































































Результаты поиска

Содержание VLT HVAC Basic Drive FC 101

Отзывы:

Danfoss VLT HVAC Basic Drive FC 101, Руководство по программированию, Страница: 100 / 104

Результаты поиска

Содержание VLT HVAC Basic Drive FC 101

Отзывы: