Danfoss VLT FC 322 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 235

Danfoss VLT FC 322 Скачать руководство пользователя страница 156

Very long control cables and analog signals may in rare cases and depending on installation result in 50/60 Hz earth loops due to noise from mains supply
cables.

If this occurs, you may have to break the screen or insert a 100 nF capacitor between screen and chassis.

The digital and analog in- and outputs must be connected separately to the VLT Automation VT Drive common inputs (terminal 20, 55, 39) to avoid
ground currents from both groups to affect other groups. For example, switching on the digital input may disturb the analog input signal.

NB!

Control cables must be screened/armoured.

1.

Use a clamp from the accessory bag to connect the screen to
the frequency converter de-coupling plate for control cables.

See section entitled

Earthing of Screened/Armoured Control Cables for

the correct termination of control cables.

5.3.14 Switches S201, S202, and S801

Switches S201 (A53) and S202 (A54) are used to select a current (0-20
mA) or a voltage (0 to 10 V) configuration of the analog input terminals
53 and 54 respectively.

Switch S801 (BUS TER.) can be used to enable termination on the RS-485
port (terminals 68 and 69).

See drawing

Diagram showing all electrical terminals in section Electrical

Installation.

Default setting:

S201 (A53) = OFF (voltage input)

S202 (A54) = OFF (voltage input)

S801 (Bus termination) = OFF

NB!

It is recommended to only change switch position at power off.

Automation VT Drive FC322 Design Guide

5 How to Install

MG.20.X1.22 - VLT

®

is a registered Danfoss trademark

155

5

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

«
...
154
155
156
157
158
...
»

Содержание VLT FC 322












































































































































































































































Отзывы:

Нет отзывов