Danfoss FC 100 Series Скачать руководство пользователя страница 48

Страница: 48 / 82

5.3.15. Class ID 29h Control Supervisory Object

The Control Supervisory Object can be used for process control and monitoring of the frequency
converter, as an alternative to the I/O Instances defined in the section “How to control the Fre-
quency Converter”.

The attributes supported for this class are listed below.

5.3.16. Class ID 0x29

Attribute

Access

Name

Data type

Min/

Max

Default

Description

Get/Set

Run 1

Bool

0-1

Run Fwd, see note below

Get/Set

Run 2

Bool

0-1

Run rev, see note below

Get/Set

NetCtrl

Bool

0-1

0 = Local Control

1 = Control from Network

Get

State

USINT

0-7

0 = Vendor specific

1 = Start up

2 = Not ready

3 = Ready

4 = Enabled

5 = Stopping

6 = Fault stop

7 = Fault

Get

Running 1

Bool

0-1

0 = Other state

1 = (Enable and Run 1)

or (Stopping and Running 1)

or (Fault Stop and Running 1)

Get

Running 2

Bool

0-1

0 = Other state

1 = (Enable and Run 2)

or (Stopping and Running 2)

or (Fault Stop and Running 2)

Get

Ready

Bool

0-1

0 = Other state

1 = Ready or Enabled or Stopping

Get

Fault

Bool

0-1

0 = No Faults Present

1 = Fault Occured (latched)

Get/Set

Fault Rst

Bool

0-1

0 = No Action

1 ->1 = Reset Fault

Get

Fault Code

UINT

Get

Ctrl From Net

Bool

0-1

0 = Control is local

1 = Control is from Network

Get/Set

DN Fault Mode UINT

0-2

Action on loss of DeviceNet

0 = Fault + Stop

1 = Ignore (Warning Optional)

2 = Danfoss specific

NB!

The ODVA drive profile selected in par. 10-10

Process Data Type Selection

is avail-

able only when Instances 20/70 or 21/71 are selected.

5. How to Access the Parameters

FC 100/ 200/ 300 DeviceNet

MG.33.D3.02 - VLT

is a registered Danfoss trademark

Содержание FC 100 Series



















































































Результаты поиска

Содержание FC 100 Series

Отзывы:

Бренды по названию

Популярные бренды

Danfoss FC 100 Series, Руководство пользователя

Результаты поиска

Содержание FC 100 Series

Отзывы:

Бренды по названию

Популярные бренды