Danfoss C67 Скачать руководство пользователя страница 68

Страница: 68 / 84

The yellow

side of the

ECL Card

isc

ellaneous

34a

Copying with the ECL Card

Check the ECL Card and the software generations (see
following example).

Insert the ECL Card with the yellow side facing you.

Go to line 8 (is not displayed), which is the ﬁrst line
below line 7.

Application type

Software

version,

ECL Card

C 7

109

Software version,
controller

Store new controller settings on the ECL Card

All new settings* can be stored on the ECL Card. Insert the ECL
Card with the yellow side facing you.

Go to line 9 (is not displayed), which is the second
line below line 7.

C 9

Copying direction

Accept to copy settings from controller to
ECL Card.

When the copying is ﬁnished, the controller returns to display
line C.

* Time and date settings are not stored on the ECL Card.

Do not remove the ECL Card while copying. The data on the ECL
Card can be damaged!

If you have copied your personal settings to the ECL Card, you
cannot restore the factory settings!

Содержание C67





















































































Результаты поиска

Содержание C67

Отзывы:

Похожие инструкции для C67

Бренды по названию

Популярные бренды

Danfoss C67, Руководство пользователя

Результаты поиска

Содержание C67

Отзывы:

Похожие инструкции для C67

Бренды по названию

Популярные бренды