Danfoss C67 Скачать руководство пользователя страница 50

Страница: 50 / 84

The grey

side of the

ECL Card

tended ser

vic

32d

Service parameter(s) 17-20

17 Inﬂuence on desired ﬂow temperature (T

ﬂow.ref(I)

)

Circuit

Setting range

Factory setting

OFF / 1 ... 20 K

OFF

The desired ﬂow temperature in heating circuit I can be

inﬂuenced by an external reference.

OFF:

The desired ﬂow temperature in circuit I is

not inﬂuenced by any other controller (slave
or circuit II).

1 ... 20:

The desired ﬂow temperature is increased
by the set value (line 17), if the demand of a
slave / circuit II is higher.

Temp.

Setting line 17

ﬂow.ref(I)

ﬂow.ref(II)

Time

Example:

If a slave controller (or circuit II) demands a higher
temperature than that of the master controller
(T

ﬂow.ref(I)

), the temperature of the master will be

increased accordingly (T

ﬂow.ref(II)

) + the setting

(line 17).

The function of line 17 can compensate for heat losses between
master and slave controlled systems.

20 Optimization based on room / outdoor temperature

Circuit

Setting range

Factory setting

(I) / (II)

ON / OFF

(OFF) / (OFF)

The optimized start and stop time can be based on either room or

outdoor temperature.

ON:

Optimization based on room temperature, if

measured.

OFF:

Optimization based on outdoor

temperature. Use this setting if the room
temperature is not measured.

Содержание C67





















































































Результаты поиска

Содержание C67

Отзывы:

Похожие инструкции для C67

Бренды по названию

Популярные бренды

Danfoss C67, Руководство пользователя

Результаты поиска

Содержание C67

Отзывы:

Похожие инструкции для C67

Бренды по названию

Популярные бренды