Dallas Semiconductor MAXIM DS21354 Скачать руководство пользователя страница 76

Страница: 76 / 124

DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers

76 of 124

RHIR: RECEIVE HDLC INFORMATION REGISTER (Address = B3 Hex)

(MSB)

(LSB)

RABT RCRCE ROVR RVM REMPTY POK CBYTE

OBYTE

SYMBOL

POSITION

NAME AND DESCRIPTION

RABT RHIR.7

Abort Sequence Detected.

Set whenever the HDLC controller sees 7 or

more ones in a row.

RCRCE RHIR.6

CRC Error.

Set when the CRC checksum is in error.

ROVR RHIR.5

Overrun.

Set when the HDLC controller has attempted to write a byte

into an already full receive FIFO.

RVM RHIR.4

Valid Message.

Set when the HDLC controller has detected and checked

a complete HDLC packet.

REMPTY RHIR.3

Empty.

A real-time bit that is set high when the receive FIFO is empty.

POK RHIR.2

Packet OK.

Set when the byte available for reading in the receive FIFO at

RHFR is the last byte of a valid message (and hence no abort was seen, no
overrun occurred, and the CRC was correct).

CBYTE RHIR.1

Closing Byte.

Set when the byte available for reading in the receive FIFO

at RHFR is the last byte of a message (whether the message was valid or
not).

OBYTE RHIR.0

Opening Byte.

Set when the byte available for reading in the receive

FIFO at RHFR is the first byte of a message.

Note: The RABT, RCRCE, ROVR, and RVM bits are latched and are cleared when read.

RHFR: RECEIVE HDLC FIFO REGISTER (Address = B4 Hex

)

(MSB)

(LSB)

HDLC7 HDLC6 HDLC5 HDLC4 HDLC3 HDLC2 HDLC1 HDLC0

SYMBOL

POSITION

NAME AND DESCRIPTION

HDLC7 RHFR.7

HDLC Data Bit 7

. MSB of a HDLC packet data byte.

HDLC6 RHFR.6

HDLC Data Bit 6.

HDLC5 RHFR.5

HDLC Data Bit 5.

HDLC4 RHFR.4

HDLC Data Bit 4.

HDLC3 RHFR.3

HDLC Data Bit 3.

HDLC2 RHFR.2

HDLC Data Bit 2.

HDLC1 RHFR.1

HDLC Data Bit 1.

HDLC0 RHFR.0

HDLC Data Bit 0.

LSB of a HDLC packet data byte.

Содержание MAXIM DS21354





























































































































Результаты поиска

Содержание MAXIM DS21354

Отзывы:

Бренды по названию

Популярные бренды

Dallas Semiconductor MAXIM DS21354, Руководство пользователя

Результаты поиска

Содержание MAXIM DS21354

Отзывы:

Бренды по названию

Популярные бренды