Daktronics TI-2031, Руководство пользователя

Страница: 17 / 24

14.500
6.500
.000
2.750
11.750
.000
4.500
PIN FUNCTION
1 CL IN-P
2 CL IN-N
3 CL OUT-P
4 CL OUT-N
5 SW IN-P
6
GND/
SW IN-N
7 BUZZER-P
8 BUZZER-N
REV
01
DATE:
7 NOV 11
ADDED TI-2031 & TI-3031 TO DIP SWITCH SETTING
BY:
MBC
02 23 MAR 15 ADDED 3000 TO DIP SWITCH SETTING NOTES KDD
03 9 NOV 15
ADDED TIME OF DAY NOTE UNDER DIP
SWITCH SETTING.ADDED P-1388 TABLE
MTR
04 2 OCT 17 UPDATED MDP DIP SWITCH SETTINGS MTR
05 24 FEB 20 UPDATED MDP DIP SWITCH SETTINGS MTR
THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING
ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY
ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF
DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES.
COPYRIGHT 2017 DAKTRONICS, INC. (USA)
THIRD ANGLE PROJECTION
PROJECT:
INDOOR SCOREBOARDS
TITLE:
INSTALLATION DWG; TI-2031/3031 LOCKER ROOM CLOCK
DATE:
24-FEB-20
DIM UNITS:
INCHES [MILLIMETERS]
SHEET REV
SCALE:
1/15 DO NOT SCALE DRAWING 1 OF 1 05
DESIGN:
MCARSRU
JOB NO. FUNC - TYPE - SIZE
1064515
DRAWN:
MCARSRU P1237 E - 10 - B
STEP 1: ATTACH REAR COVER TO WALL
-THE CLOCK SHIPS WITH TWO DIFFERENT REAR COVERS (FLUSH MOUNT AND SURFACE MOUNT)
-THE FLUSH MOUNT OPTION REQUIRES CUTTING A HOLE IN THE WALL AND INSTALLING A 120VAC OUTLET
INTERNAL TO THE WALL. OVERALL DEPTH OF CLOCK PROTRUDING FROM THE WALL IS 1.375". SEE
SUGGESTED CUTOUT AND OUTLET LOCATION IF THIS OPTION IS CHOSEN.
-THE SURFACE MOUNT OPTION INSTALLS OVER ANY EXISTING 120VAC OUTLET. THE WALL PACK
TRANSFORMER IS CONCEALED BEHIND THE REAR COVER. OVERALL DEPTH OF CLOCK IS 3.25"
-CHOOSE DESIRED REAR COVER AND USE AS A JIG TO MARK THE MOUNTING HOLE LOCATIONS
AT CHOSEN CLOCK LOCATION.
-DRILL HOLES IN WALL AT MARKED LOCATIONS AND INSTALL APPROPRIATE WALL ANCHORS (CUSTOMER SUPPLIED)
-PLACE REAR COVER OVER ANCHORS AND SECURE TO WALL WITH APPROPRIATE SCREWS (CUSTOMER SUPPLIED)
THROUGH KEYHOLES IN REAR COVER.
STEP 2: ROUTE/TERMINATE SIGNAL AND POWER
-ROUTE SIGNAL CABLE TO THE REAR LEFT SIDE OF CLOCK LOCATION AND ALLOW IT TO EXTEND
AT LEAST 12" BEYOND THE WALL
-CONNECT SIGNAL WIRE TO PLUG P-1388 SIGNAL TERMINAL. CONNECT THE RED SIGNAL WIRE TO THE
POSITIVE ( + )
JACK LABELED "CL-IN" AND THE WHITE SIGNAL WIRE TO THE NEGATIVE ( - ) JACK LABELED
"CL-IN"
-SET DIP SWITCHES AS SHOWN IN THE CHART AT RIGHT BASED ON CONTROLLER TYPE.
SWITCH POSITION UP IS ON, SWITCH POSITION DOWN IS OFF
-PLUG THE WALL PACK TRANSFORMER INTO THE POWER JACK LOCATED BELOW THE SIGNAL TERMINAL,
AND PLUG THE WALL PACK INTO THE ELECTRICAL OUTLET.
STEP 3: ATTACH FRONT CLOCK ASSEMBLY TO REAR COVER
-COIL UP ANY EXTRA SIGNAL/POWER WIRES IN REAR COVER OR WALL
DEPENDING ON MOUNTING METHOD CHOSEN
-SLIDE FRONT CLOCK ASSEMBLY ONTO REAR COVER
-ATTACH FRONT CLOCK ASSEMBLY TO REAR COVER WITH INCLUDED SCREWS
(THREE ON TOP AND THREE ON BOTTOM)
DIP SWITCH SETTING:
TI-2031
ALLSPORT 1600/3000/5000
SWITCH 1: ON
SWITCH 6; ENABLE T.O.D.= ON
SWITCH 7: ON
ALL SPORT 4000
SWITCH 7: ON
PROSPORT 6000
SWITCH 6: ON
TI-3031
ALL SPORT 5500
SWITCH 1: ON
SWITCH 6: ENABLE T.O.D.= ON
P-1388 TABLE
FRONT VIEW
(SUGGESTED CUTOUT AND OUTLET LOCATION
FOR FLUSH MOUNT REAR COVER)
2X4 STUDS
120VAC
OUTLET
SHEETROCK
WALL ANCHORS
@2
FRONT ROTATED VIEW
(FLUSH MOUNT REAR COVER)
2X4 STUDS
SHEETROCK
WALL CUTOUT
MOUNTING SCREWS
120VAC OUTLET
FRONT ROTATED VIEW
(SURFACE MOUNT REAR COVER)
EXISTING
120VAC OUTLET
MOUNTING SCREWS
2X4 STUDS
SHEETROCK
FRONT ROTATED VIEW
TRANSFORMER
KNOCKOUTS FOR OPTIONAL
POWER/SIGNAL ROUTING
LOCATED ON TOP AND BOTTOM
OF REAR COVER
FRONT CLOCK ASSEMBLY
SIGNAL WIRE
REAR COVER
FRONT ROTATED VIEW
FRONT CLOCK ASSEMBLY
P-1388 SIGNAL
TERMINAL BLOCK
POWER JACK
FOR TRANSFORMER
SEE DETAIL A
DIP SWITCH LOCATION
REAR ROTATED VIEW
SEE DETAIL A
DETAIL A
SCALE 2/3
DIP SWITCHES GO FROM 8-1
LEFT TO RIGHT
SWITCH POSITION UP IS ON
SWITCH POSITION DOWN IS OFF
TRANSFORMER
POWER JACK
P-1388
SPRING CRIMP