Dakota Digital BIM-01-2-HLLY Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 12

Dakota Digital BIM-01-2-HLLY Скачать руководство пользователя страница 1

[1]

MAN #650588D

BIM-01-2-HLLY

Bus Interface Module for Holley EFI

This Bus Interface Module is designed to read engine information from specific Holley EFI kits. The Holley Terminator,
HP, Sniper, Dominator and Terminator X and X Max. The module is connected to the Holley EFI through the CAN-bus
plug on the EFI harness. Depending on your EFI module you may have a 2-pin or 4-pin CAN connector. We supply EFI
adapter harnesses that will allow you to connect with your particular kit.

There are two interface (I/O) ports on the BIM-01-2-HLLYmodule. Either one can be connected to the instrument system
or to another module, allowing several units to be daisy chained together.

Cannot daisy chain with GPS-50-2

.

Do not connect the I/O port to anything other than a Dakota Digital control box or BIM.
Do not mount the module in the engine compartment; as

it should be mounted in the vehicle’s cabin.

The engine and transmission information that is available from the unit depends on the EFI kit and module programming
and add-ons. For specific data readings: see individual setups below for each version of Holley EFI system below.

1
2
3
...
»

Содержание BIM-01-2-HLLY













Отзывы:

Нет отзывов