Dakota Digital 3X Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

MAN 650067:G

15

CHECK ENG (-)

The CHECK ENG terminal is used with fuel injection ECM’s to display engine problems

and trouble codes. The CHECK input is activated by a ground signal from the ECM. Whenever
the check input is grounded, the system will display a flashing “E” in the upper left corner of the
message display.

When the ECM is placed into diagnostic mode, trouble codes can be read by counting

the flashes. Consult a service manual for the fuel injection system that you have for further
information on trouble codes.

With some ECM’s, a 12 volt light bulb may need to be connected in addition to the

CHECK input in order to provide proper current loading. Connect one wire from the bulb to
keyed power and the other to the CHECK input. In this case, both the bulb and our display
system indicator would come on when the check engine wire is “active”.

AUX. I/O

This jack is used to connect bus expansion modules (BIM). Do not attempt to plug in any

other device to this jack or damage to the control box will occur.  This connector should be left
open, unless using a Dakota Digital product designed for it.  Operation is discussed with BIM
units purchased separately.

DISPLAY RIBBON CABLE

This is where the grey cable from the display system plugs into the control box.

To connect the ribbon cable from the display system to the control box;

•

First open the two locking tabs on either side of the blue RIBBON CABLE connector.

•

Next align the red stripe in the ribbon cable with the “STRIPE” text on the control box.

•

Finally press the ribbon cable into the connector, press firmly to seat the connector.

•

The two locking tabs should “snap” into place securing the connector.

***Do NOT force the connector, if it is not inserting easily, check alignment of the red
stripe on the ribbon cable with the indicator on the control box.

Locking tabs CLOSED

Locking tabs OPEN

Align stripe

Ribbon cable connected

RED STRIPE

LOCKS
CLOSED

«
...
13
14
15
16
17
...
»

Содержание 3X Series





































Отзывы:

Нет отзывов

Похожие инструкции для 3X Series

Бренд: Vega Страницы: 76

Бренд: 3Doodler Страницы: 24

Бренд: Hagan Страницы: 32

Бренд: Jetter Страницы: 4

Бренд: K&K Страницы: 8

Бренд: K&K Страницы: 20

Бренд: K&K Страницы: 6

Бренд: K&K Страницы: 3

Бренд: K&K Страницы: 3

Fast PLUG 500 premium

Бренд: SAGEMCOM Страницы: 2

WorkCentre Pro 123

Бренд: Xerox Страницы: 4

Бренд: Harol Страницы: 17

Бренд: Cab Technology Страницы: 10

Бренд: Panamorph Страницы: 2

Бренд: Z-Wave Страницы: 10

WaterGuard CM2300

Бренд: Mobeye Страницы: 32

Бренд: PROAIM Страницы: 3

Бренд: UBEXi Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды