Dakota Digital 3X Series Скачать руководство пользователя страница 30

Страница: 30 / 36

MAN 650067:G

Symptom

Possible Problem

Solution

-----------------------------------------------------------------------------------------------------------------------------------

The fuel display reads

The control box may be set for

Refer to “Fuel Setup”

backwards, incorrectly,

the wrong type of fuel sender.

section of the installation manual

or does not change.

to ensure that the settings match

your fuel sender.

The fuel sender may not be

Check the connections at both

connected to the control box

ends of the fuel sender wire.

properly.

Make sure the fuel sender is

grounded properly.

The fuel sender may not be

Check the fuel sending unit with

operating properly.

an electrical multi-meter.

The fuel sender may have a

Use the custom fuel sender setup.

non-standard resistance

See the “Fuel Setup” section of the

range.

manual for instructions.

The oil or water display

The sending units are not grounded Make sure wires are in correct terminals.

reading is incorrect.

to the control box.

The sending unit wire is picking

Isolate the sending unit wire from

up noise from nearby wires.

engine and ignition wires.

The sending unit is not

Use the sending unit provided with

compatible with the control box

the display system.

The gear shift indicator

The optional gear shift sending

Connect the sending unit to the

does not light up.

unit is not connected to the

control box using the

control box.

instructions supplied with the

sending unit.

The gear shift decoder is not

Check gear shift decoder

calibrated properly.

Installation manual.

The gear shift indicator

The gear shift decoder

Check the connections to the

does not operate

is not connected properly.

transmission linkage and to

properly.

the control box.

Check gear shift decoder

Installation manual.

The internal turn signal

The control box is not connected

Check the wires connected to the

and high beam

to the vehicle's electrical

HIGH, LEFT, and RIGHT

indicators do not light up.

system properly.

terminals on the control box.

The Check Engine

The control box is not connected

This feature is designed to work

indicator does not

to an engine control module.

with engine control systems that

operate properly.

provide an active low signal.

Содержание 3X Series





































Результаты поиска

Содержание 3X Series

Отзывы:

Похожие инструкции для 3X Series

Бренды по названию

Популярные бренды

Dakota Digital 3X Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3X Series

Отзывы:

Похожие инструкции для 3X Series

Бренды по названию

Популярные бренды