background image

Model 9016 X-Purge Operator Interface 

 

Daisy Data Displays, Inc. 

February 2022 

15 

D010-000002 

8

 

Trouble-Shooting Guide 

8.1

 

Division 1 X-Purge Trouble-Shooting 

PROBLEM 

POSSIBLE CAUSE 

SUGGESTED SOLUTION 

When power is applied, the 

purge status indicator light 

does not come on 

Power is not connected to 

the unit 

Connect AC power to the power 

connection on the purge system. 

Ensure that the power switch is on. 

Ensure that AC power is on. 

Improper line voltage 

selection 

Ensure that the 120/240 VAC switch 

on the purge control is set 

appropriately for your power 

source. 

After power is applied, the 

purge status indicator stays 

solid red; it does not switch to 

yellow or blink 

No air supply to unit 

Ensure that a purge gas line is 

connected to the unit and that the 

supply line is “on.” The pressure 

gauge on the air-in box should 

indicate a higher pressure than 20 

PSI 

Restrictions in air line 

Ensure that supply line and inlet 

connect have no restrictions and 

that the supply line is not kinked 

Restrictions in main purge 

line inside enclosure 

Ensure that the main purge line 

(terminating in a brass tee fitting) is 

not kinked or disconnected 

Leaks in the enclosure 

Ensure that all access doors are 

closed and latched. Ensure that all 

access panels are closed and sealed. 

There should be no holes or 

openings in the enclosure. 

The purge status indicator is 

yellow, but the enclosure 

takes an excessively long time 

to complete the purge (when 

the status indicator turns 

green) 

Low purge gas supply 

pressure 

Increase purge gas inlet pressure at 

the air-in regulator or on the main 

supply line 

Restriction in the main purge 

line 

Ensure that the main purge line 

within the enclosure (ending in a 

brass tee fitting) is not kinked or 

obstructed 

Purge status indicator flashes 

yellow and purge takes an 

excessively long time to 

complete. 

Low purge gas supply 

pressure 

Increase purge gas inlet pressure at 

the air-in regulator or on the main 

supply line 

Purge or operation stops and 

purge status indicator flashes 

red code 

Fatal purge error 

See Table 6.1 X-Purge Status Light 

Key on page 12. 

 

Содержание 9016 X-Purge








































Отзывы: