background image

Model 9016 X-Purge Operator Interface 

Daisy Data Displays, Inc. 

February 2022 

D010-000002 

4

 

Installation 

4.1

 

PAC-Seal Connection Instructions 

A conduit seal is necessary for most equipment enclosures in hazardous areas. Consult 

your local codes for full guidance. 
It is 

very important

 that knowledgeable personnel, familiar with national and local 

codes, supervise hazardous area equipment installations. 

The sealing compound generally used for PAC-seals is an inorganic, chemically setting, 

magnesium oxide base material, which develops a slight expansion while hardening 

into a porcelain-like body. Sealing Compound is supplied as a powder and need only 

be mixed with water to apply. Approximately one ounce of sealing compound is 

needed per cubic inch of space to be filled. 

IMPORTANT 

The sealing compound powder has a shelf life of six months when stored in

unopened, tightly sealed containers in a dry location at 70

°

F.

Any equipment accidentally splashed with sealing compound should be

cleaned with soap and water before the sealing compound cures.

Equipment Required 

Four PAC-Seal fittings, 1” NPT or 0.75” NPT for the X-Purge (2 for conduit

connection at the enclosure or I/O casting, 2 for connection in the safe area), or

sealing conduits.  The PAC Seal and conduit size selected will depend on the size

and number of conductors, which must be run to the unit. Check with NEC tables to

determine the conduit size necessary

Conduit for electrical signals and for electrical power (separate runs), NEC and NFPA

approved for use in hazardous areas

NEC and NFPA approved flexible conduit if needed for difficult installations

Fittings as required for permanent conduit installation NEC and NFPA approved for

use in hazardous areas

Signal cables, power cables, and connectors as required to mate with the

equipment within the enclosure or cast aluminum box

AC power switch for use in the safe area

IMPORTANT 

ALWAYS follow NEC, NFPA, and local codes when installing conduit and PAC-seals 

in hazardous areas!

 

Содержание 9016 X-Purge








































Отзывы: