Daikin Modular L Smart Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 90

background image

ESIE19-06

|

Part 2. Troubleshooting

2.2. Error based troubleshooting

21/01/20

|

Version 1.1

Page 25

Modular L Smart

2.2.1.5. “A1-01” – PCB abnormality

2.2.1.6. “A6-00” – Fan motor abnormality

2.2.1.7. “A8-00” – Power supply malfunction

Trigger

Effect

Reset

EEPROM data is not received correctly.

Unit will stop operating.

Power reset via HRV unit.

Possible cause

Check

Corrective action

HRV unit - Electrical components

Faulty indoor PCB.

Check if error still occurs after turning off
power and turning it back on again.
Check if the indoor PCB receives power.
Check if the HAP LED is blinking in regu-
lar intervals.
Check if the correct spare part is installed.
Check the wiring to indoor PCB.

Adjust power to the indoor PCB.
Replace indoor PCB when HAP LED is
not blinking in regular intervals.
Install correct spare part or update indoor
PCB.
Adjust wiring to indoor PCB when
required.

Trigger

Effect

Reset

The rotation speed of the fan motor is not
detected while the output voltage to the
fan is at its maximum.

Control will perform some retry to operate
fan motor.
When retries fail, unit will stop operating.

Power reset HRV unit.

Possible cause

Check

Corrective action

Faulty indoor PCB.

Check if error still occurs after turning off
power and turning it back on again.
Check if the indoor PCB receives power.
Check if the HAP LED is blinking in regu-
lar intervals.
Check if the correct spare part is installed.
Check the wiring to indoor PCB.

Adjust power to the indoor PCB.
Replace indoor PCB when HAP LED is
not blinking in regular intervals.
Install correct spare part or update indoor
PCB.
Adjust wiring to indoor PCB when
required.

Faulty indoor fan motor.

Check the fan motor.
Check fan motor connections and wiring.

Replace fan motor when required.
Adjust wiring when required.

Indoor fan motor locked.

Switch off the power.
Turn fan manually.

Replace fan motor when the fan does not
turn smoothly.

Trigger

Effect

Reset

Power supply at main PCB is not correct.

Unit will stop operating.

Power reset HRV unit.

Possible cause

Check

Corrective action

Power supply is not correct.

Voltage & frequency within tolerance.
Correct contact circuit breaker.
Correct cable specification.

Adjust power supply.

«
...
23
24
25
26
27
...
»

Содержание Modular L Smart



























































































Отзывы:

Нет отзывов

Похожие инструкции для Modular L Smart

Бренд: RDZ Страницы: 56

Бренд: RDZ Страницы: 32

Бренд: BLAUBERG Ventilatoren Страницы: 12

Бренд: Flexit Страницы: 12

Amana ARUF 14 Series

Бренд: Maytag Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды