Daikin Modular L Smart Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 90

background image

ESIE19-06

|

Part 5. Appendix

5.1. Field setting

Modular L Smart

Page 76

21/01/20

|

Version 1.1

4. Press the Up/Down buttons to select the required ventilation mode. For more information about ventilation modes, see Ventilation modes in the installer and user reference guide.

Ventilation modes

You can change the ventilation mode in the main menu.

Time to clean filter indication

When it is time to clean the filters, the following message or icon shows at the bottom of the basic screen: time to clean the filter.

To remove time to clear filter indication

Press the Menu/Enter button.

Press the Up/Down buttons to select Reset Filter Indicator.

Press the Menu/Enter button.

About error indications

If an error occurs, there is an error icon in the basic screen and the operation lamp blinks. If a warning occurs, ONLY the error icon blinks and the operation lamp does NOT. Press the
Menu/Enter button to display the error code or warning and contact information.

The error code blinks and the contact address and model name appear as shown below.

In this case, notify your Daikin dealer about the error code.

Mode

Description

Auto mode

Using information from the air conditioner (cooling, heating, fan, and set temperature) and heat reclaim ventilation unit (indoor and outdoor
temperatures), this mode automatically changes between Energy Reclaim Ventilation and Bypass mode.

Energy Reclaim Ventilation mode

The outdoor air is supplied to the room after passing through a heat exchange element, where heat is exchanged with the return air.

Bypass mode

The outdoor air bypasses the heat exchange element. This means that outdoor air is supplied to the room without heat exchange with the return air.

«
...
74
75
76
77
78
...
»

Содержание Modular L Smart



























































































Отзывы:

Нет отзывов

Похожие инструкции для Modular L Smart

Бренд: Daikin Страницы: 16

RIS 1900 VWL EKO 3.0

Бренд: Salda Страницы: 89

Бренд: Fujitsu Страницы: 48

Бренд: Bryant Страницы: 68

Бренд: VES Страницы: 16

Бренд: Master Страницы: 15

Бренд: FläktGroup Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды