Daikin MicroTech III Скачать руководство пользователя страница 50

Страница: 50 / 68

ED 15103-6 • MICROTECH III WSHP UNIT CONTROLLER 50 www.DaikinApplied.com

eleCTed

arameTers

nformaTIon

Table 23:

Bit Description for Enfinity Large Two Compressor (Models CCH/CCW and LVC/LVW)

Bit

Number

Bit Description

Setting

Description

Unit Controller Jumpers

Normal/Test Mode

Jumper 1 = Open (0)

Normal operation

Jumper 1 = Shorted (1)

Service/Test mode operation

Fan Operation

Jumper 2 = Open (0)

Continuous fan operation

Jumper 2 = Shorted (1)

Cycling fan operation

Loop Fluid

Jumper 3 = Open (0)

Water loop fluid

Jumper 3 = Shorted (1)

Glycol loop fluid

Freeze Fault Protection

Jumper 4 = Open (0)

LWT Freeze Fault Protection is disabled

Jumper 4 = Shorted (1)

LWT Freeze Fault Protection is enabled

Room Sensor Setpoint Adjust Range

Jumper 5 = Open (0)

Short range: -5º to +5º F (-2.78º to +2.78º C)

Jumper 5 = Shorted (1)

Long range: 55º to 95º F (12.78º to 35º C)

Thermostat/Room Sensor

Jumper 6 = Open (0)

Thermostat control

Jumper 6 = Shorted (1)

Room sensor control

6 & 7

Compressor Availability (2 Jumpers)

Jumper 7 = Open (0)

Both compressors are available for use

Jumper 8 = Open (0)
Jumper 7 = Shorted (1)

Lead compressor is available for use (lag compressor is off-line)

Jumper 8 = Open (0)
Jumper 7 = Open (0)

No compressors are available for use

Jumper 8 = Shorted (1)

Unit Controller Inputs

Compressor #1 Low Pressure Switch

Switch Closed (1)

Low Pressure Switch for compressor #1 is normal

Switch Open (0)

Low Pressure Switch for compressor #1 is in alarm

Compressor #1 High Pressure Switch

Switch Closed (1)

High Pressure Switch for compressor #1 is normal

Switch Open (0)

High Pressure Switch for compressor #1 is in alarm

Emergency Shutdown

Open (0)

Unit shuts down

Local Occupancy Switch

Switch Open (0)

Unoccupied

Switch Closed (1)

Occupied

Thermostat Heat Stage #3

(O – Terminal)

Switch Closed (1)

Third stage of thermostat heating is requested

Thermostat Fan Request

(G – Terminal)

Switch Closed (1)

Thermostat fan operation is requested

Thermostat

Cool Stage #1 / Cool Stage #2

(Y1 – Terminal)

Switch Closed (1)

First stage of thermostat cooling is requested

(unit has HGR option)

Second stage of thermostat cooling is requested

(unit does not have HGR option)

Thermostat

Cool Stage #2 / Cool Stage #3

(Y2 – Terminal)

Switch Closed (1)

Second stage of thermostat cooling is requested

(unit has HGR option)

Third stage of thermostat cooling is requested

unit does not have HGR option)

Thermostat Heat Stage #1

(W1 – Terminal)

Switch Closed (1)

First stage of thermostat heating is requested

Thermostat Heat Stage #2

W2 – Terminal)

Switch Closed (1)

Second stage of thermostat heating is requested

I/O Expansion Module Jumpers

Not Used

Jumper 1 = Open (0)

Not Used

Jumper 2 = Open (0)

20 & 21

Secondary Heating Options

(2 Jumpers)

Jumper 3 = Open (0)

None

Jumper 4 = Open (0)
Jumper 3 = Shorted (1)

Supplemental electric heat

Jumper 4 = Open (0)
Jumper 3 = Open (0)

Boilerless electric heat

Jumper 4 = Shorted (1)
Jumper 3 = Shorted (1)

Hydronic Heating

Jumper 4 = Shorted (1)

1. This switch is effective only when the network scheduling is not in use.

Содержание MicroTech III





































































Результаты поиска

Содержание MicroTech III

Отзывы:

Похожие инструкции для MicroTech III

Бренды по названию

Популярные бренды

Daikin MicroTech III, Лист данных по продажам и инженерии

Результаты поиска

Содержание MicroTech III

Отзывы:

Похожие инструкции для MicroTech III

Бренды по названию

Популярные бренды