Daikin MicroTech III Скачать руководство пользователя страница 3

Страница: 3 / 68

nTroduCTIon

www.DaikinApplied.com

ED 15103-6 • MICROTECH III WSHP UNIT CONTROLLER

nTroduCTIon

Revision History

ED 15103

Sep-08

Initial release.

ED 15103-1

Mar-10

Changed default baud rate to 38400 (BACnet

MS/TP Setup).
Corrected range and descriptions of setpoint

shift parameters (Protocol Point Summary).

Moved BACnet Configuration section (BACnet

Configuration).
Added references to no flow control (BACnet

Configuration and BACnet Terminal Settings).

Changed the Type Category for all Multistate

Values from Enumerated to Unsigned (Detailed

Protocol Point Information). Changed BACnet PICS

Application Version to 2.6 and Firmware Revision

to 2.7

ED 15103-2

Mar-11

Updated nvoBinaryIn and nvoBinaryOut status

for dual compressors or dual stage capacity

compressor, with automatic multiple fan speed

control. New nciSetpoints heating & cooling

“standby” default values. Updated nciHtgSptHiLim

and nicClgSptLoLim to also limit long range setpoint

adjust input. Added BACnet PIC statement for two-

stage compressor control.

ED 15103-3

Jun-12

Added SmartSource variables and updated

BACnet PIC statements. Range changes to:

nciLowEwtSptGly, nciLowEwtSptWtr. Added new

alarms. Modify low pressure alarm delay range.

Added the following configuration properties:

nciSptAdjMax, nciSptAdjMin, nciLowLwtDiff,

nciHydroClgOnSpt. Added the humidistat variables:

nviHumidistat and nvoHumidistat. Added the fan

switch nviFanOnAuto variable. Deleted Dual Stage

compressor references. Updated Daikin McQuay

logo and associated references.

ED 15103-4

Jun-16

Modified hydronic heating range and default values.

Added note to nviFanOnAuto (MSV3) to indicate

auto selection forces cycling fan. Added note to Fan

On/Auto Status for SmartSource v6.0 and higher.

Added totalizer variables. Added Enfinity Large

Two Compressor and SmartSource GCV models.

Updated BACnet PIC statements. BACnet device

instance updates. Daikin Applied branding, major

formatting updates. Corrected MSV:2 and MSV:5

BACnet alarms #13-15.

ED 15103-5

Sep-16

Revised description to Application Mode Input.

Also added note to data tables that the following

variables revert to default Null after reboot:

Application Mode Input, Space Temp Input,

Temp Setpoint Input, Temp Setpoint Offset Input,

Humidistat Remote Input, Compressor Enable

Input, Occ Override Input, Occ Scheduler Input,

Occ Sensor Input, Aux Heat Enable Input, Energy

Hold Off Input. Changed MSV:1 from Read-only to

Commandable in data tables.

ED 15103-6

Jul -18

Updates to formatting. Changed description for

AV:24, AV:25, AV:27, AV:28 and nvoSetptShift to

indicate the value represents the local hardwired

setpoint adjustment value from the room sensor

potentiometer. Added row and switch data to Table

22, bit 29 & 30. Removed Dirty Filter alarm from

nvoUnitStatus,Table 16.

Notice

throughout the world
Daikin Applied reserves the right to change any information

contained herein without prior notice. The user is responsible

for determining whether this product is appropriate for his or

her application.
™ ® The following are trademarks or registered trademarks

of their respective companies: BACnet from American Society

of Heating, Refrigerating and Air-Conditioning Engineers, Inc.

Echelon,

orks

, LonMark, and LonTalk from Echelon

Corporation, Daikin Applied, Applied Terminal Systems,

Smartsource, Enfinity, and MicroTech III from Daikin Applied.

Limited Warranty

Consult your local Daikin Applied representative for warranty

details. To find your local Daikin Applied representative, go to

www.DaikinApplied.com.

Reference Documents

Number

Company

Title

Source

078-0014-01G

LonMark

Interoperability

Association

LonMark

Layers

1-6 Interoperability

Guidelines, Version 3.4

www.lonmark.org

078-0120-01G

LonMark Application

Layer Interoperability

Guidelines, Version 3.4

8503

WSHP Functional Profile

078-0156-01G Echelon

Corporation

orks

FTT-

10A Free Topology

Transceiver Users Guide

www.echelon.

com

IM 927

Daikin Applied

MicroTech III

Water Source Heat

Pump

orks

Communication Module

Installation Manual

www.

DaikinApplied.

com

IM 928

MicroTech III Water

Source Heat Pump

BACnet Communication

Module Installation

Manual

OM 931

MicroTech III Water

Source Heat Pump Unit

Controller Operation and

Maintenance

OM 1085

MicroTech III Water

Source Heat Pump

Software Downloading

Procedures and

Troubleshooting Guide

Содержание MicroTech III





































































Результаты поиска

Содержание MicroTech III

Отзывы:

Похожие инструкции для MicroTech III

Бренды по названию

Популярные бренды

Daikin MicroTech III, Лист данных по продажам и инженерии

Результаты поиска

Содержание MicroTech III

Отзывы:

Похожие инструкции для MicroTech III

Бренды по названию

Популярные бренды