Daikin Magnitude Скачать руководство пользователя страница 70

Страница: 70 / 70

IOM 1210-7

(6/18)

Daikin Applied Training and Development

Now that you have made an investment in modern, efficient Daikin Applied equipment, its care should

be a high priority. For training information on all Daikin Applied HVAC products, please visit us at

www.DaikinApplied.com

and click on Training, or call 540-248-9646 and ask for the Training Department.

Warranty

All Daikin Applied equipment is sold pursuant to its standard terms and conditions of sale, including

Limited Product Warranty. Consult your local Daikin Applied representative for warranty details. To find

your local Daikin Applied representative, go to

www.DaikinApplied.com

Aftermarket Services

To find your local parts office, visit

www.DaikinApplied.com

or call 800-37PARTS (800-377-2787).

To find your local service office, visit

www.DaikinApplied.com

or call 800-432-1342.

This document contains the most current product information as of this printing. For the most up-to-date

product information, please go to

www.DaikinApplied.com

Products manufactured in an ISO Certified Facility.

Содержание Magnitude







































































Результаты поиска

Содержание Magnitude

Отзывы:

Похожие инструкции для Magnitude

Бренды по названию

Популярные бренды

Daikin Magnitude, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnitude

Отзывы:

Похожие инструкции для Magnitude

Бренды по названию

Популярные бренды