Daikin LXE10E-A4 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 162

Daikin LXE10E-A4 Скачать руководство пользователя страница 27

2-14

2.5 OPERATION MODES AND CONTROL

There are two main types of operation modes: the cargo cooling control mode and the unit
inspection mode.
The cargo cooling control mode is explained in this section.

※

For the unit inspection mode, refer to section 3.9.

The relationship between the operation mode and setting temperature is as follows.

※

For details, refer to section 2.5.1 to 2.5.4

Operation mode

Setting temperature

Control sensor

Operation description

Frozen mode

–10.1˚C to –30.0˚C

Return air

Compressor ON/OFF control

(+13.8˚F to –22.0˚F)

temperature sensor

Partial frozen

–3.0˚C to –10.0˚C

Return air

Capacity control operation

mode

(+26.6˚F to +14˚F)

temperature sensor

with suction modulating valve

and hot-gas bypass control

+25.0˚C to –2.9˚C

Supply air

Capacity control operation

Chilled mode

(+77˚F to +26.8˚F)

temperature sensor

with suction modulating valve

and hot-gas bypass control

Defrosting mode

–

–

Hot-gas defrosting with

refrigerant metering control

https://daikin-p.ru

«
...
25
26
27
28
29
...
»

Содержание LXE10E-A4



































































































































































Отзывы:

Нет отзывов