Daikin LXE10E-A4 Скачать руководство пользователя страница 146

Страница: 146 / 162

6-15

6.5.2 Short circuit operation of controller

For cutting off

Turn the circuit breaker OFF.

the power to

Disconnect the power supply

CPU board

connector CN82(White) on SMV

adapter board.

For making the

Remove Short Circuit Connector

forced running

SCC1-1(Blue), SCC1-2(Red) and

of COMP.,

SCC2(Blue) stored on back of

CFM and EFM.

controller.

Connect Short Circuit Connector

SCC1-1(Blue) to CN8 and SCC2

SCC1-2(Red) to CN8 and SCC2

(Blue) to CN9 on terminal board.

(Blue) to CN10 on terminal board.

Disconnect CN82 (White)

Open cover

SMV adapter

SCC1-1(Blue)

SCC2(Blue)

SCC1-2(Red)

For checking

Turn the circuit breaker ON.

reverse phase

If the power is in reverse phase,

power

COMP. can not be run and CFM

EFM runs reversely with high speed.

runs reversely.

Then fresh air is sucted to Outlet

Hole and discharged from Inlet Hole

at the ventilator.

For correcting

If it is in reverse phase, turn the circuit breaker OFF and replace the

reverse phase

reverse phase correction socket to opposite side.

power

("Lower socket CN-C1 to Upper CN-C2" or "Upper CN-C2 to Lower CN-C1")

Air Outlet

Air Intake

Cooling Operation

Heating Operation

SCC1-2(Red)

SCC2(Blue)

Terminal Board

CN5(Red)

SCC1-1(Blue)

SCC2(Blue)

CN-C1 & CN-C2 : Reverse phase
correction socket (Refer to next step

)

EMERGENCY

[COOL] BLUE [COOL] BLUE

[HEAT] RED

CN8

CN9

EMERGENCY

[HEAT] BLUE

CN10

EMERGENCY

[COOL] BLUE [COOL] BLUE

[HEAT] RED

CN8

CN9

EMERGENCY

[HEAT] BLUE

CN10

https://daikin-p.ru

Содержание LXE10E-A4



































































































































































Результаты поиска

Содержание LXE10E-A4

Отзывы:

Daikin LXE10E-A4, Руководство по обслуживанию, Страница: 146 / 162

Результаты поиска

Содержание LXE10E-A4

Отзывы: