Daikin LXE10E-A4 Скачать руководство пользователя страница 112

Страница: 112 / 162

4-10

(3) Removal of excess refrigerant oil after

compressor replacement

The oil plug, oil level gauge and "Removing oil
label" are fitted on the spare parts compressor.

™

When the compressor is replaced to spare
parts compressor, remove the excess
refrigerant oil in the following procedure.

1. Connect manifold to the discharge and

suction ports.

2. Operate the unit for about 5 minutes.

3. Stop the unit.

4. Conduct oil return operation by using the

short PTI function of controller.

(1) Set the ON/OFF switch to ON.

(2) Push and hold the

key for 3 seconds

to enter PTI selection mode.

(3) Selecting the "S-PTI" mode using the

key and pushing the

key

activates the short PTI. Then, conduct

"P06" , "P08" steps displayed on the

LED.

P06/HPS check:

When the high pressure rises, the

circulation amount increases to return

the refrigerant oil to the compressor.

P08/Pump down check:

Evaporates the refrigerant contained in

the compressor oil.

(4) When "P10" is displayed on the LED,

stop the unit.

→

←

Oil plug

Excess oil

Oil

REMOVING EXCESS COMPRESSOR

OIL IS NOT COMPLETED.

REMOVE EXCESS COMPRESSOR OIL.

THEN TAKE OFF THIS LABEL

8. Close the oil plug when no more oil comes

out.

9. Take off "Removing oil lavel" sticked on

compressor body.

6. Bypass gas from high pressure side to low

pressure side of gauge manifold, adjust the

low pressure to 0kPa or more.

7. Loosen the oil drain plug and remove the

excess oil.

5. If the oil level can be seen on the oil level

gauge, conduct the step 4 oil return

operation again.

Removing
oil lavel

oil plug

oil level gauge

Remo

excess oil

https://daikin-p.ru

Содержание LXE10E-A4



































































































































































Результаты поиска

Содержание LXE10E-A4

Отзывы:

Daikin LXE10E-A4, Руководство по обслуживанию, Страница: 112 / 162

Результаты поиска

Содержание LXE10E-A4

Отзывы: