Daikin FTXZ25NV1B Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 48

Daikin FTXZ25NV1B Скачать руководство пользователя страница 8

7

Names and functions of parts

Remote controller

Notes on remote controller

•  Take care to avoid dropping the remote controller or getting it wet. (Dropping or getting it wet may break it.)
•  When the remote controller gets dirty, wipe it with a dry soft cloth.
•  Signal communication may become poor if an electronic-starter-type fl uorescent lamp (such as inverter-type lamps) or TV is in the room.

Consult the service shop if that is the case.

• The sensitivity may become poor if the transmitter/receiver is exposed to direct sunlight.

Display (LCD), with backlight

• Displays the operating conditions.

(All displayed here for your reference.)

• Press any of the operation buttons to light

the backlight for about 5 seconds.

• Before use, peel off the protection sheet.

Direct operation buttons

Starts the COOLING, “SARARA” DRY,
HEATING or “URURU” HUMIDIFY operation.



Page 11

Transmitter/Receiver

Transmitter/Receiver

• Sends/receives signals to/from the indoor

unit.

• The remote controller must be used with the

transmitter/receiver pointed towards the
transmitter/receiver of the indoor unit.
Transmission will fail if there is an
obstruction such as a curtain between the
remote controller and indoor unit.

• The maximum distance for communication is

about 7m.

AUTO button

Automatically selects an appropriate operation
mode (COOLING or HEATING) based on the

indoor temperature and starts the operation.



Page 11

OFF button

Stops the operation.



Page 11

Cover

After you open the cover, close it
completely. The buttons on the
cover will not function properly if
the cover is not securely closed.

Cover

TEMPERATURE button

Adjusts the temperature setting.



Page 12

HUMIDITY button

Adjusts the humidity setting.



Page 12

FAN button

Adjusts the airfl ow rate setting.



Page 13

OFF TIMER button

Sets the time until the operation stops.



Page 18

FLASH STREAMER AIR PURIFYING /
FRESH AIR SUPPLY VENTILATION
button

• Performs streamer discharge.
• Fresh air is taken in from outside.



Page 24

Model

ARC477A1

01_EN_3P338603-1C.indd 7

9/28/2013 2:32:17 PM

«
...
6
7
8
9
10
...
»

Содержание FTXZ25NV1B

















































Отзывы:

Нет отзывов