Daikin FTXZ25NV1B Скачать руководство пользователя страница 41

Страница: 41 / 48

When the OPERATION lamp (green) blinks

OPERATION lamp (green)

When the TIMER lamp (orange)

blinks



Page 36

When the MOLD PROOF /

CLEANING FILTER lamp (green)
blinks



Page 37

Dummy

Attention

•

When

is pressed for about

5 seconds when the
OPERATION lamp is not
blinking, “00” is displayed.

• For other possible failures.



Page 41 - 45

When the OPERATION lamp (green) blinks, turn off the

circuit breaker. After about 1 minute, turn it on again and

start operation.

If the OPERATION lamp still blinks, check the error code according to the steps below and
take appropriate action.

< To check the error code >

Direct the remote controller toward the
indoor unit and press

for about

5 seconds.

• An error code is displayed on the LCD.

Check the error code and take the action described
below.

Error code

Check operation and action

Is the air fi lter soiled or dusty?

• Stop the operation and start the CLEANING FILTER

operation.



Page 28

Turn off the circuit breaker and turn it on again. Then start operation.

Is any foreign object stuck in the outdoor unit fan?

• Turn off the circuit breaker, and then remove foreign objects.

F3,F6,L3,L4,L5

Is the air outlet of the outdoor unit blocked by a car or the
like?

• Turn off the circuit breaker, and then remove the obstruction.

Turn on the circuit breaker and start operation.

Other error codes

Check the model name (or control code *) and contact the service

shop.

Check the OPERATION lamp again and take the action

described below.

OPERATION lamp

Action

Lights up

Continue the operation for a while and if the OPERATION lamp
does not blink, keep on using the air conditioner.

Blinks again

Check the model name (or control code *) and contact the
service shop.

< * To check the control code >

Press

again while the error code is

displayed on the LCD.

• A 4-digit control code is displayed on the LCD.

If the model name cannot be checked with the indoor unit, use
this control code for the inquiry.

The following error code indicates an error of the humidifying unit or some sensors.

Only the COOLING and HEATING operations are available in this case. Contact the
service shop as soon as possible.

PH, PA, P9, CC, CA, U7

When the Need Arises



Sec. 5

01_EN_3P338603-1C.indd 40

9/28/2013 2:33:19 PM

Содержание FTXZ25NV1B

















































Результаты поиска

Содержание FTXZ25NV1B

Отзывы:

Daikin FTXZ25NV1B, Руководство по эксплуатации, Страница: 41 / 48

Результаты поиска

Содержание FTXZ25NV1B

Отзывы: