background image

2

 | 

Components

Service manual

137

FTXA20~50A(W)(S)(T) + FTXA20~50B(B)(S)(T) + RXA42+50A +
RXA20~35A(9) + RXA42+50B
Split Stylish R32
ESIE18-03D – 2021.05

2.16 Streamer unit

2.16.1 Checking procedures

1

As  there  is  no  specific  check  procedure  for  this  component,  first  perform  a
check of the indoor unit main PCB to check if the streamer unit needs to be
replaced. See 

"2.8.1 Checking procedures"

 [

4

 75].

After complete check of the indoor unit
main PCB, is the problem solved?

Action

Yes

No further actions required.

No

Replace the streamer unit, see

"2.16.2 Repair procedures"

 [

4

 137].

2.16.2 Repair procedures

To remove the streamer unit

Prerequisite: 

Stop the unit operation via the user interface.

Prerequisite: 

Turn OFF the respective circuit breaker.

Prerequisite: 

Remove the required plate work, see 

"2.14 Plate work"

 [

4

 120].

1

Disconnect the connector from the streamer unit.

b

a

a

Streamer unit connector

b

Streamer unit

2

Click the streamer unit out of the indoor unit.

3

To install the streamer unit, see 

"2.16.2 Repair procedures"

 [

4

 137].

Содержание FTXA20A

































































































































































































Отзывы: