Daikin Altherma 3 ECH2O Скачать руководство пользователя страница 46

Страница: 46 / 68

Faults and malfunctions

Installation and maintenance instructions

Daikin Altherma EHS(X/H)(B)-D

Heat pump (indoor unit) with integrated heat accumulator

008.1444099_01 – 11/2018 – EN

Code

Component/Designation

Error

Possible fault rectification

E9014 High-pressure switch S1PH

in the refrigerant system

refrigerant

high

Pressure in refrigerant system is too high.

▪ High-pressure switch S1PH or fan motor defect-

ive.

▪ Check, replace.

▪ Poor wiring contact.

▪ Flow rate in the heating system too low.

▪ Filled refrigerant quantity too high.

▪ Check, replace.

▪ Service valves in the heat pump outdoor unit not

open.

▪ Open the service valves.

E9015 Pressure sensor S1NPH in

the heat pump outdoor unit

refrigerant

low

Pressure in refrigerant system too low.

▪ Refrigerant quantity too low.

▪ Check, eliminate cause, top up refrigerant.

▪ Pressure sensor S1NPH in the heat pump out-

door unit defective.

▪ Temperature sensor of fin heat exchanger R4T in

the heat pump outdoor unit defective.

▪ Solenoid valve in the heat pump outdoor unit not

opening.

▪ Main circuit board in the heat pump outdoor unit

defective.

▪ Check, replace.

E9016 Electronic overload protec-

tion in the refrigerant com-
pressor

Compressor load protection

Refrigerant compressor overload protection has
triggered. Pressure difference in the refrigerant cir-
cuit between high and low pressure side too high
(> 26 bar).

▪ Refrigerant compressor defective.

▪ Inverter circuit board in the heat pump outdoor

unit defective.

▪ Refrigerant compressor/inverter circuit board wir-

ing, poor contact.

▪ Filled refrigerant quantity too high.

▪ Check, replace.

▪ Service valves in the heat pump outdoor unit not

open.

▪ Open the service valves.

E9017 Fan motor in the heat pump

outdoor unit

Ventilator blocked

▪ A fan in the heat pump outdoor unit is blocked.

▪ Check the fan for dirt or blockages; if neces-

sary, clean and free up.

▪ Fan motor defective.

▪ Fan motor wiring, poor contact.

▪ Overvoltage at fan motor.

▪ Fuse in the heat pump outdoor unit defective.

▪ Inverter circuit board in the heat pump outdoor

unit defective.

▪ Check, replace.

E9018 Electronic expansion valve

Expansion valve

The electronic expansion valve in the heat pump
outdoor unit is defective, replace.

E9019 Storage tank temperature

sensor t

DHW2

Hot water temperature > 85 °C

The storage tank temperature sensor t

DHW2

delivers

a temperature value > 85 °C.

Sensor or connecting cable defective.

▪ Check, replace.

E9020 Outlet temperature sensor

(hot gas sensor) R2T on
the heat pump outdoor unit
refrigerant compressor too
high

Evaporator

high

▪ Outlet temperature sensor R2T on the refrigerant

compressor or connecting cable defective.

▪ Refrigerant compressor defective.

▪ Check, replace.

Содержание Altherma 3 ECH2O




































































Результаты поиска

Содержание Altherma 3 ECH2O

Отзывы:

Бренды по названию

Популярные бренды

Daikin Altherma 3 ECH2O, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Altherma 3 ECH2O

Отзывы:

Бренды по названию

Популярные бренды