background image

3

Mandatory

Mandatory

Mandatory

Mandatory

Mandatory

Forbidden

Forbidden

Caution

Forbidden

Mandatory

Mandatory

Mandatory

Forbidden

Mandatory

Mandatory

Check

CAUTION

If a large quantity of refrigerant is filled in the site, 
people in the site may be anesthetized or 
suffocated. With the CE model, MSDS (Material 
Safety Data Sheet) for the refrigerant is attached to 
the product. Take an action according to the MSDS.

WARNING

If refrigerant leaks, provide thorough ventilation.

If an abnormal condition occurs, stop operation 
of the unit, and leave it unused until the cause of 
the trouble is securely removed. Failure to 
observe this instruction may result in damage to 
the unit, electric shock, fire or injury.

If an abnormal condition occurs, stop operation immediately.

Be sure to use a commercial power supply. 
Using an inverter power supply may result in 
burnout.

Use a commercial power supply.

To ensure safety, a cover or casing is mounted to 
rotary parts. Do not put a finger or foreign object 
in an aperture of the cover or casing. Failure to 
observe this instruction may result in injury.

Do not put a finger or foreign object in an aperture of the unit.

After stopping operation, be sure to turn OFF the 
circuit breaker.

Turn OFF the circuit breaker.

Pollution of the operating liquid causes the unit 
service life to be shortened. Use thorough 
caution about pollution of the operating liquid to 
maintain the pollution degree at NAS10 or lower 
level.

Perform daily control of operating liquid pollution.

Before you start running the main machine, 
cancel the operation lock status with the Oil 
Cooling Unit operation panel. If you start the main 
machine in the operation lock status, the unit 
cannot control the operating liquid temperature, 
which may result in damage to the machine.

Cancel operation lock before running the main machine.

Do not use this unit in special atmosphere, 
including dust, oil mist, high temperature or high 
humidity.

Do not use the unit in special atmosphere.

Before executing a trial run, make sure that the 
main machine is set in safe conditions (the main 
machine will not run, or no accident occurs even 
if the main machine runs.)
Failure to observe this instruction may result in 
injury or damage to the machine.

Ensure safety of the main machine before trial run.

Do not put an obstacle within 500 mm from the 
air intake/exhaust port.
If air intake/exhaust flow is blocked, this unit may 
not provide the specified cooling capacity.

Do not put an obstacle near the air intake/exhaust port.

Clean the air filter at least every two weeks.
If the air filter is clogged, the cooling capacity 
deteriorates, and power consumption increases.

Clean the air filter periodically.

Do not sit or step on this unit. Failure to observe 
this instruction may result in fall or overturn of 
the unit, causing injury.

Do not step on the unit.

Before start of operation, make sure that the tank 
is filled with operating liquid to an appropriate 
level.

Check liquid level in the tank.

Fasten this unit securely so that it will not be moved 
by vibration or external force during transportation. 
If storing vibration or external force is applied to the 
unit, the internal equipment may be damaged.

During transportation, fasten the unit securely.

Before start of operation, make sure that the 
electric wiring are properly conducted, and 
connecting parts are securely tightened.

Check the unit before operation.

Otherwise, you may cut your hand with the 
condenser fin edges. Furthermore, the internal 
compressor or motor frames and the refrigerant 
piping become extremely hot. If you touch these 
parts with bare hands, you may get a burn.

When cleaning the unit, wear gloves.

PIM00132A_EN.fm  3 ページ  2007年9月20日 木曜日 午後3時4分

Содержание AKZJ8Series













































Отзывы: