Dai VKM100GBMV1 Скачать руководство пользователя страница 14

13

3P130768-6L   English

11 FIELD SETTING AND TEST RUN

11. 1 PERFORM FIELD SETTINGS WITH THE 

REMOTE CONTROLLER

(1) Make sure the control box lids are closed on the indoor 

and outdoor units.

(2) Depending on the type of installation, make the field 

settings from the remote controller after the power is 
turned on, following the “Field Settings” manual which 
came with the remote controller.

Lastly, make sure the customer keeps the “Field Settings” 
manual, along with the operating manual, in a safe place.

11. 1. 1 FIELD SETTING
Using the remote controller of the VRV-system air 
conditioner to make Heat Reclaim Ventilator unit settings

<Initial setting>

“MODE NO.” 17,18 and 19: Group control of Heat Reclaim 
Ventilator units.

“MODE NO.” 27, 28 and 29: individual control

<Operating procedure>
The following describes the operating procedure and 
settings.

(1) Press the INSPECTION/TRIAL button for more than four 

seconds with the unit in the normal mode to enter the local 
setting mode.

(2) Use the TEMPERATURE ADJUSTMENT button to select 

the desired “

MODE NO.

”. (The code display will blink.)

(3) To make settings for individual units under group control 

(when mode No. 27, 28 or 29 is selected), press the TIMER 
SETTING ON/OFF button to select the “

unit No.

” for which 

the settings are to be made. (This process is not necessary 
when settings are made for the entire group.)

(4) Press the top section of the TIMER button to select the 

FIRST CODE NO.

”.

(5) Press the lower section of the TIMER button to select 

SECOND CODE NO.

”.

(6) Press the PROGRAM/CANCEL button once to enter the 

settings. (The code display will stop blinking and light up.)

(7) Press the INSPECTION/TRIAL button to return to normal mode.

<Example>

When adjusting the ventilation air flow to low setting in the 
group setting mode, enter the Mode No., “19” FIRST CODE 
NO., “0” and SECOND CODE NO., “01”.

S

ETTING

MODE NO.

S

ECOND 

CODE NO.

FIELD 

S

ET MODE

FIR

S

CODE 
NO.

UNIT No.

GROUP

(3)

(3)

(1) (7)

(6) (4) (5)

(2)

(4) (5)

01_EN_3P130768-6L.fm  13 ページ  2013年3月21日 木曜日 午前11時48分

Содержание VKM100GBMV1





















Отзывы: