background image

4

FEATURES DIAGRAM

1

Door latch - When the door is closed it

will automatically lock shut. If the door is
opened while the oven is operating. The
magnetron will automatically shut off.

2

Door seal - The door seal maintains the

microwave within the oven cavity and pre-
vents microwave leakage.

3

Oven cavity.

4

Spatter shield - Protects the microwave

outlet from splashes of cooking foods.

5

Safety interlock system - Prevents the
oven from operating while the door is
opened.

6

Door release button - Pushing this but-

ton stops oven operation and opens the
door.

7

Glass cooking tray - Made of special
heat resistant glass. The tray must
always be in proper position before oper-
ating. Do not cook food directly on the
tray.

8

Roller guide - Supports the glass cooking

tray.

9

Door screen - Allows viewing of food.
The screen is designed so that light can
pass through, but not the microwaves.

0

Time set pad - Used to set the cooking

time and the present time.

q

Display - Cooking time, power level, pre-

sent time are displayed.

w

Speedy cook - Touch to set the any

desired reheat setting.

e

Baked potato - Used to cook baked pota-

to.

r

Beverage - Used to reheat beverage.

t

Feeding bottle - Used to sterilize bottle.

y

Frozen pizza - Used to reheat frozen

pizza.

u

More - Used to add on one touch cooking.

i

Less - Used to remove one touch cooking.

o

Power - Used to set power level.

p

Fresh vegetable - Used to blanch fresh

vegetable.

a

Auto defrost - Used to defrost foods.

s

Clock/A.start - Used to set clock & Used

to set auto start.

d

Stop/Clear - Used to stop the oven oper-

ation or to delete the cooking data.

f

Start - Used to start a selected operation.

Содержание KOR-612L0S
























































Отзывы: