Daewoo DWD-UD123X Скачать руководство пользователя страница 62

Страница: 62 / 77

6) LACK OF DRY PERFORMANCE

• Situation : after drying, the clothes still get wet.

cause)

☞

The laurdry amount is more than the recommendation capacity 7.0kg.

☞

Condensing cold water is not supplied.

☞

Clogging Bellows Duct results in poor air circulation.

checking method)

• Situation after drying, the clothes was soaked and hot.

cause)

☞

The dry is done from bad spin performance because of unbalance.

☞

no spin was done before the dry had started.

• Situation : PCB shows "H1" or "H3".

cause)

☞

Thermistor is broken.

☞

Thermistor is short or cut-off.

countermeasures)

☞

replace the Thermistor.

part name

checking point

checking results

jurge

repair method

BELLOWS

DUCT

VALVE INLET

+Condensing

HOSE

clogging
bellows duct

no water supply
from inlet valve

heater was
overheated
owing to poor air
circulation

VALVE INLET
connector slipped
out

VALVE INLET
broken

ill-connection of
condensing hose to
duct pipe

clean the bellow
duct

connect normally

replace valve inlet

connect normally

BELLOW

DUCT

VALVE INLET

CONDENSING

HOSE

Содержание DWD-UD123X














































































Результаты поиска

Содержание DWD-UD123X

Отзывы:

Похожие инструкции для DWD-UD123X

Бренды по названию

Популярные бренды

Daewoo DWD-UD123X, Руководство по обслуживанию

Результаты поиска

Содержание DWD-UD123X

Отзывы:

Похожие инструкции для DWD-UD123X

Бренды по названию

Популярные бренды